Why won t my chevy silverado remote start?

There could be several reasons why your Chevy Silverado’s remote start is not working. Here are some common issues to check:
Improper Starting Procedure
Make sure you are following the correct starting procedure for your remote start system. Press the lock button on your key fob once, then hold the remote start button (usually shaped like an arrow) for at least 2 seconds or until the turn signal lamps flash. Keep holding the button, and the vehicle should start.
Vehicle Not in Park
The remote start system will only work if the car is in Park. Make sure the vehicle is in Park, disengage and re-engage the Park position before retrying the starting procedure.
Too Many Remote Start Attempts
If you have pressed the remote start button twice in quick succession, it may not work. To resolve this, insert the key into the ignition, turn it on and off, exit the vehicle with the key fob, and retry the starting procedure.
Coolant and Oil Pressure
Check the engine coolant and oil temperatures. If the temperatures are not within the required range, the remote start system may not function properly.
Check Engine Light
If the Check Engine Light or Malfunction Indicator Lamp (MIL) is illuminated, it could indicate a fault that is preventing the remote start system from working. In this case, it is recommended to fix the underlying issue causing the fault.
These are some of the common reasons why a Chevy Silverado’s remote start may not be working. It’s important to note that these suggestions are general and may not cover all possible causes. If the issue persists, it may be best to consult your vehicle’s manual or contact a certified technician for further assistance.
Let me know if there’s anything else I can help with!

How do I get my remote starter out of valet mode?

Now the second way to get it out of valet is to turn the ignition. On we’re going to take lock and trunk at the same time. And it blinks twice to let us know that it’s out of valet.

Why my remote start is not working?

Most times, the only reason your remote control loses programming is because you have a dead battery. Car remote starts can keep programming through some type of memory installed in its features. However, like any computer, sometimes they lose memory. When this happens, the only way to fix it is by calling Auto Image.

Why is my truck remote not working?

Causes of a Car Remote Not Working
The most common problem with these car key fobs is that the batteries go dead over time, in which case replacing the battery should fix the problem. You may also have a problem with the internal contacts, the buttons, or another physical part of the fob.

Why is my remote start not working in my Silverado?

Double check your engine coolant and oil temperatures: If the engine coolant temperature is too high or the oil pressure is too low, remote start is disabled! After you have let the car cool down for 5-10 minutes and rechecked the levels, retry the start procedure.

How do you remote start a Chevy Silverado?

How to Use Chevy Remote Start with Your Key Fob

1. Press the lock button on your key fob to secure the vehicle.
2. Immediately after pressing the lock, press and hold the remote start button for at least four seconds.
3. If successful, your vehicle’s lights will flash and the engine will start to run.

Why is my car not recognizing my key fob?

The most common culprit behind an electric key fob’s failure is, as you might guess, the battery. This is a relatively easy issue to fix, although you may need to get a ride to get to buy a replacement fob battery.

Why is my Chevy remote not working?

Why did my key fob suddenly stop working? Your Chevy key fob stopped working because the coin cell battery needs to be replaced. The keyless entry remote control uses a small watch-type battery, typically a CR2032 or DL 2032 to operate. Watch batteries are designed to last approximately 3 years.

How do I reset my Chevy remote?

On the Chevy key fob, press and hold the “Unlock” and “Lock” buttons at the same time until you hear the door lock and unlock again. This means you’re all set. Re-insert the programmed key back into the ignition to the “On” position to finish the Chevy key fob programming process.

How do I make my Chevy remote start work?

Here’s how it. Works. If you’re within 197 feet aim your key fob at the vehicle depending on your vehicle. You may or may not need to press the lock.

Why is my remote start not working and Check Engine Light on?

If the ‘Check Engine Light’ or Malfunction Indicator Lamp (MIL) is illuminated, the remote start will not work. Don’t panic, one of the reasons the MIL can illuminate is due to a loose gas cap! Reseal the cap, restart the car, and retry step #1!