Where is the radio code on an Acura?

Finding the Radio Code on an Acura
If you need to find the radio code for your Acura, you can locate it in the following ways:
1. Anti-Theft ID Card: The Radio/Navigation Code and the device unit’s serial number are listed on the anti-theft ID card that comes with the vehicle. The card is usually placed in the glove box at the time of delivery.
2. Navigation System Serial Number Label: The navigation system serial number label is located on the control unit, where the removable DVD is stored. The serial number cannot be obtained electronically on the navigation screen.
3. Acura Radio Code Retrieval Website: You can retrieve unlock codes for Radio and Navigation Devices at https://radio-navicode.acura.com/ using your vehicle’s VIN and Device Serial Number.
4. Acura Owner’s Manual: There is an anti-theft identification card in your owner’s manual, with numbers listed in the lower right corner. The longer, bottom number is the radio code.
It’s important to keep the radio code in a secure location, as it is necessary to make the radio operational in case of a battery reset or disconnection.
Remember to keep this code safe for future use!

Why does my Acura radio say code?

How to Find and Use Your Acura Radio Code. Step inside the cabin of your vehicle and start the engine. The radio should still say “CODE” — when it says this, all that it means is that the security system was engaged due to a loss in power from your battery.

What are common radio codes?

Radio Codes

• 10-0 Use Caution.
• 10-1 Weak Signal.
• 10-2 Good Signal.
• 10-3 Stop Transmitting.
• 10-4 Affirmative.
• 10-5 Relay to/from.
• 10-6 Busy.
• 10-7 Out of Service.

How do I start my radio without the code?

Bypass radio code
To do so, restart the car engine and turn on the radio. If a code is asked, turn off the radio. Afterward, press and hold the radio button for a few seconds or up to a couple of minutes, enough time for the system to ditch the code.

How many digits is Acura radio code?

five digit
A small sticker in your glovebox, on your door jamb, or trunk jamb. The sticker should contain two series of numbers. The top five digit series of numbers is your radio code. The bottom series of numbers is your serial number.

Can I get my radio code from my VIN number?

If the manufacturer that built your vehicle offers online code lookup, you typically enter your VIN, the serial number of the radio, and contact information, including phone number and email. The code may be emailed to you for your records.

Where can I find my Acura radio code?

Device Serial Number: Radio Codes
The card is usually placed in the glove box at the time of delivery. The Radio/Navigation Code and the device unit’s serial number are listed on the anti-theft ID card that comes with the vehicle. The card is usually placed in the glove box at the time of delivery.

How do I find my 4 digit code for my Honda radio?

How to Find Your Honda Radio Code: Step-By-Step Guide

1. Steps for Obtaining Your Honda Radio Code: 1) Go to radio-navicode.honda.com.
2. 2) Check your Anti-Theft Radio Identification Card.
3. 3) Check your Service History Book.
4. 4) Look in your glove box and center console.
5. 5) Schedule a Service Appointment at Planet Honda.

How do I find my 4 digit radio code?

Try these places first: Glovebox – Some radio codes appear on a sticker in the glovebox. Vehicle handbook – You might find the code in your vehicle handbook under the stereo or security section. Alternatively, some codes are printed on a small paper or plastic card, found inside the handbook.

How can I get my Acura radio code without a serial number?

Specifics vary, but the Acura radio code is typically located in the glove box or engine fuse box. If the radio code isn’t present, it may be in your owner’s manual or can be found on the official Acura website when you enter your VIN. If you can’t find it, our Acura service center can help.

How do I reset my car radio?

Then locate the power button on the radio. Which is typically located on the left side of the radio’s control panel. Once you have located the power button press and hold it for 20 seconds. While.