Location of the Drain Plug on a Ford Ranger
The drain plug on a Ford Ranger is typically located on the oil pan at the bottom of the engine. It is used to drain the engine oil during an oil change.
Source: ‘Factory Oil Drain Plug | Page 2 | 2019+ Ford Ranger and Raptor…’
In the case of the Ford Ranger, the drain plug is described as a USB flange bolt with a seated rubber ring. It is designed to be a lifetime item and does not have a replaceable washer. The drain plug is a very robust 15mm head with a flange and a big O-ring, and it should be good for the life of the vehicle. It is recommended to inspect the O-ring during each oil change to ensure its integrity.
Source: ‘Factory Oil Drain Plug | 2019+ Ford Ranger and Raptor Forum (5th…’
It’s important to note that the specific location of the drain plug may vary slightly depending on the model year and engine type of the Ford Ranger. However, it is generally located at the lowest point of the oil pan.
If you need further assistance or have any other questions, feel free to ask!
Contents
- What size is the drain plug on a Ford Ranger?
- How often do you need to replace a drain plug?
- How do you drain the water out of a Ford Ranger?
- Where is the drain oil drain?
- What size socket do I need to remove a drain plug?
- Where is the drain plug located?
- Where is the oil drain plug on a 2011 Ford Ranger?
- How much oil does a 3.0 v6 Ford Ranger take?
- Where is the oil drain in my car?
- Where is the oil sump plug located?
What size is the drain plug on a Ford Ranger?
Dorman Engine Oil Drain Plug 090-175.1
Program: oil-tite. 15 mm head. Shank length: 1″. Head size (SAE/metric): 15 mm.
How often do you need to replace a drain plug?
After removal, the majority of automobiles do not need a new drain plug. Unless a new drain plug is advised by the manufacturer, I only replace a drain plug if it is broken or worn. A drain plug gasket is often reusable, while some gasket varieties are only intended for one use.
How do you drain the water out of a Ford Ranger?
Up. Foreign we’re gonna let that drain.
Where is the drain oil drain?
Look under the car and locate the drain plug: It is a large nut or plug located under the oil pan (large tank) at the bottom of the engine.
What size socket do I need to remove a drain plug?
Place a 3/8-inch (0.9 centimeters) socket in the socket wrench, fit it over the drain plug’s nut and turn it counterclockwise. The oil drain plug should open easily, draining the used oil from the engine. Make sure to place a bucket and some newspaper under the car’s engine to catch all the draining oil.
Where is the drain plug located?
And is located uh you want to put it underneath the oil drain plug. This is your oil pan. This is the plug you will open this plug.
Where is the oil drain plug on a 2011 Ford Ranger?
As well as the oil filter. Right up there they’re both in the same spot. So let’s get a collection bucket. And start draining. Use a 13-millimeter socket break this free it shouldn’t be too tight.
How much oil does a 3.0 v6 Ford Ranger take?
4.5 quarts
Capacity: With filter 4.5 quarts. When refilling, remove dipstick to provide adequate venting and allow oil to flow into crankcase. After refill, check oil level.
Where is the oil drain in my car?
The drain plug is a large nut or plug located under the oil pan at the bottom of the engine. If you can’t reach your oil drain plug easily, you’ll have to either crawl under your car to reach it or jack up the car.
Where is the oil sump plug located?
Use a work light or flashlight to look under your car. You should be able to see and reach a large nut or plug located under the oil pan at the bottom of the engine (see Figure 13-6). This is the oil drain plug.
