AHG Auto Service » Make » Chevrolet » Where is the crankshaft position sensor located on a Chevy Malibu?

Where is the crankshaft position sensor located on a Chevy Malibu?

The crankshaft position sensor on a Chevy Malibu is located behind the starter, next to the oil pressure sensor [[8]]. To access it, you may need to remove the starter, at least partially .
Please note that there are different engine configurations for the Chevy Malibu, so the exact location of the crankshaft position sensor may vary depending on the specific model and year of your vehicle. It is always a good idea to consult the vehicle’s manual or seek professional assistance for accurate information.
If you are looking to replace the crankshaft position sensor, you can find compatible parts at auto parts stores like Advance Auto Parts . The cost of a replacement sensor can range from $18.49 to $34, depending on the brand and store .
Remember to let the engine control unit (ECU) relearn optimal performance strategies after replacing the sensor, which may take a couple of drives.
I hope this information helps! Let me know if there’s anything else I can assist you with.

Where is the exact location of the crankshaft position sensor?

It’s going to be right where the flywheel is you got the crankshaft position sensor there and it’s magnetic sensor and it detects. The the angle and degrees of this uh crankshaft right there.

Is it easy to replace crankshaft position sensor?

It’s technically possible to replace a crankshaft position sensor yourself, but it’s much less painful to have an expert do it. Because the crankshaft position sensor lies in such a sensitive region of the engine, amateur mechanics run the risk of causing further damage by attempting a MacGyver-style fix.

What are symptoms of a bad crankshaft sensor?

Here are some common symptoms:

  • Trouble starting the engine. If the sensor is not sending the correct signals, the ECU may not know when to trigger fuel injection and ignition, leading to difficulties starting the vehicle.
  • Intermittent stalling.
  • Check Engine Light is on.
  • Poor acceleration.
  • Fuel efficiency concerns.

What happens when a camshaft sensor goes bad?

Because the data from the CMP sensor(s) is often used as an input for everything from fuel injector timing to VVT operation, a bad sensor can potentially lead to a variety of engine performance problems. Examples include misfiring, rough running, lack of acceleration, and stalling.

How do you reset a crankshaft position sensor?

Clear select continue once crank pattern clear is complete select crank pattern. Learning select continue the relearn is complete. Now isn’t that quicker than what you might be doing.

Will an engine start without a crank sensor?

The Crankshaft Position Sensor (CKP) is used by the computer to determine where the crankshaft is on the #1 cylinders’ cycle in order to determine when to time the spark and fuel injection. Without it, the engine will not start because there will be no ignition and in many instances, no fuel injection either.

Will a car start with a bad crankshaft position sensor?

If your crankshaft sensor is bad, your car usually won’t start. This is because your engine doesn’t get any information from the ECU or PCM regarding your crankshaft, so the vehicle will think there’s a transmission or fuel injection problem.

What is the difference between a cam sensor and a crank sensor?

What does a Camshaft/Crankshaft Position Sensor do? The Camshaft sensor determines which cylinder is firing to establish injector synchronization and coil firing sequence in DIS systems. Crankshaft sensors set ignition timing, supply the RPM signal, and determine engine speed.

What will happen if the crankshaft position sensor is failure to operate?

Engine misfires – If the crankshaft position sensor is not functioning properly, it can cause the engine to misfire. This can be due to an incorrect signal being sent to the computer, or no signal at all. Rough idling – Another symptom of a faulty crankshaft position sensor is rough idling.

What codes will a bad crankshaft sensor cause?

The OBD-II code P0335 is a generic diagnostic trouble code that stands for “Crankshaft Position “A” Circuit Malfunction.” The code is set when your car’s primary computer—also known as the powertrain control module (PCM)—is unable to detect a signal from the crankshaft position sensor.

AHG Auto Service

At AHG, we are committed to always providing our Perth customers with the best service and benefits when it comes to their vehicle servicing and repair needs. We have over 30 passenger and commercial vehicle dealerships in WA and can handle all of your car servicing needs no matter the make or model.

Leave a Comment