Where is the BCM on a 2017 Ford Explorer?

Location of Body Control Module (BCM) on a 2017 Ford Explorer
The Body Control Module (BCM) on a 2017 Ford Explorer is located under the dashboard on the driver side towards the center of the vehicle. Some of the signs of a defective or bad BCM include blinking lights on the dashboard, electronics such as windshield wipers stop functioning intermittently, and slow acceleration.
It’s important to note that the BCM is also referred to as the Smart Junction Box, Multi-function module, or the GEM, and all have the same part number. It was located to the left side behind the radio in some instances.
If you are experiencing issues with the BCM, it’s crucial to heed warning signs, take prompt action, and seek help. Delaying action could cause further vehicle damage or even a system-wide failure.
I hope this information helps! If you have any further questions or need additional assistance, feel free to ask.

Where is the secondary fuse box?

The secondary under-hood fuse box is next to the battery. To open it, push the tabs as shown. If something electrical in your vehicle stops working, check for a blown fuse first. Determine from the chart on pages and , or the diagram on the fuse box lid, which fuse or fuses control that device.

How do I reset my Ford BCM?

Resetting the BCM on a Ford F-150 is as simple as disconnecting or turning off the battery, giving the vehicle a little bit of time and then reconnecting or restarting the battery. Its important to wait at least 15 minutes between draining the vehicle completely and restarting it.

How do you reset the airbag module on a Ford Explorer?

Steps to Reset Your Ford’s Airbag Module:

1. Step 1: Safety Precautions.
2. Step 2: Locate the Airbag Module.
3. Step 3: Disconnect the Module.
4. Step 4: Wait for Discharge.
5. Step 5: Reconnect the Module.
6. Step 6: Reconnect the Battery.
7. Step 7: Turn On the Ignition.
8. Step 8: Test the Airbag System.

Where is the fuse box in a Ford Explorer?

I have a 2012 Ford Explorer Limited. And I will show you the fuse box locations. This video will apply to Ford Explorers made from 2011 all the way up to 2015. Now it might also apply to 2016 to 2019.

Where is the BCM on a 2014 Ford Explorer?

The BCM is under the instrument panel on the driver side. See the link below for location and replacement steps. Yes that is correct, the BCM and the interior fuse panel are one and the same.

Where is the BCM module located?

The BCM is typically located underneath the dashboard. This seems to be standard on most vehicles, as this location is near the cabin switches. Replacing a BCM can be costly and usually requires programming by a dealer.

Where is the airbag control module located?

Where is the Airbag Module Located. The control unit is the core of the airbag system and is located in the centre of the vehicle, under the radio or behind the steering wheel. Normally located in the area of ​​the dashboard or sometimes under the front seats of the vehicle.

How do you reset the airbag module on a 2017 Ford Explorer?

Here are the steps to reset your Ford airbag module:

1. Step 1: Disconnect the Battery. The first step is to disconnect the battery to ensure that there is no power flowing through the airbag system.
2. Step 2: Remove the Airbag Module.
3. Step 3: Reset the Module.
4. Step 4: Reinstall the Module.
5. Step 5: Reconnect the Battery.

Where is the BCM on a 2014 Ford Edge?

At the Body Control Module (BCM), located in the LH lower kick panel, remove the lower kick panel fuse cover and the RCM fuse 41 (7.5A) from the BCM. For additional information, refer to the Wiring Diagrams Manual.

Where is the BCM located on a Ford Ranger?

Repair of the customers own unit • Supply a fully programmed exchange unit (customer must provide the original unit) Injectronics only require the BCM for testing and repair of the above listed faults. The BCM is located on the driver’s side of the vehicle underneath the dash panel.