Where do you put the jack stands on a Chevy Traverse?

To properly place jack stands on a Chevy Traverse, you can follow these guidelines:
1. Look for the jack points: On the Traverse, the jack points are typically located on the pinch welds under the vehicle. These are reinforced areas along the underside of the vehicle’s body where it is safe to lift the vehicle using a jack. The pinch welds are usually located just behind the front wheels and just in front of the rear wheels.
2. Lift the vehicle using a jack: Before placing the jack stands, you will need to lift the vehicle using a jack. Refer to the owner’s manual or a reliable source for the specific location of the jack point and how to properly lift the vehicle.
3. Place the jack stands: Once the vehicle is lifted, carefully position the jack stands under the appropriate jack points. The jack stands should be placed on a sturdy part of the vehicle’s frame or suspension components to ensure stability and safety. Avoid placing the jack stands on any plastic or non-reinforced areas.
4. Lower the vehicle onto the jack stands: Slowly and carefully lower the vehicle onto the jack stands, ensuring that they are securely supporting the weight of the vehicle. Double-check that the jack stands are properly positioned and engaged before working underneath the vehicle.
It’s important to note that the exact location of the jack points may vary depending on the specific model year and trim level of the Chevy Traverse. Therefore, it’s always a good idea to consult the owner’s manual or seek guidance from a trusted source for your specific vehicle.
Remember to always prioritize safety when working with a jack and jack stands.
I hope this information helps! Let me know if you have any other questions.

Where do you put a jack stand traverse?

Set the jack stand underneath the pinch points of your vehicle. The pinch points are located on the sides of your vehicle behind your front tires or in front of your rear tires. Slide your jack stand in from the side of your vehicle.

Can you put jack stands under the axle?

It depends what you are working on! If I were working on the axle, I’d put them under the chassis frame (or jacking points on a monocoque vehicle), but if I was working on the shell, brakes, diff etc I usually put them under the axle tube.

Where do you put the jack under an SUV?

Locate the jack point on the vehicle
Your owner’s manual should give you the location of jack points. Usually there’s one on each side behind the front wheels and in front of the back wheels, close to the rocker panels. There may be central jack points located behind the bumpers (front and rear).

Can I use a 2 ton jack on a SUV?

For example, a full-size family saloon will probably only need a jack with a 2-ton capacity to lift it. The best car jack for an SUV or 4×4, meanwhile, may need a capacity of at least 3 tons. One of the most important factors to consider is how much your trolley jack can lift.

How do you jack up a 2012 Chevy Traverse?

We have this vehicle on our to post lift. But if you’re gonna lift it up in your driveway. You could put a floor jack under here on the subframe on either side and jack up the car.

Can a Chevy Traverse be lifted?

Getting ready for the trail means more than just finding the right Chevy Traverse lift kit. It also means supporting your lifted Chevy Traverse with upgrades that put additional torque into your power profile, as well as those that will help you keep your traction when the terrain challenges your driving skills.

How many jack stands do I need?

If it’s just one end, use two jack stands. If it’s the entire vehicle you’re lifting, be sure to use four. In case you’re working on soft earth, like grass or asphalt, you can place thick plywood to prevent the jack stands from sinking.

Where should jack stands be placed?

If you’re lifting the car to get under it, to do some work, or to change the oil, you must place a jack stand under the rocker panel near the jack and snug it up to the car’s body. This will ensure that the car cannot fall on you, should the jack slip or fail entirely.

Can you put jack stands on pinch welds?

Yeah, the pinch weld can be jacked anywhere. I’ve done it before where I jacked on the front edge and put the stand on the actual lift point behind it.

Do you need jack stands to change a tire?

What you NEED is a SAFE way to keep the vehicle elevated while working on it. Jack stands do that job very well. But maybe you have something else at hand that will work too. I used to have a couple of stubby pieces of logs around to set the car down onto.