What year Fords have a Dana 60 front axle?

The Ford Dana 60 front axle has been used in various Ford models over the years. Here is some information about the years in which Ford vehicles have been equipped with the Dana 60 front axle:
– In the mid-1970s, Ford started using the Dana 60 front axle.
– Ford still uses the Dana 60 front axle.
– Most Ford Dana 60s and all 2005+ Dana 60s have 35 spline axle shafts.
– The 1999-2004 Ford Super Duty trucks were equipped with leaf-sprung Dana 60 front axles.
– The 2005-up Ford Super Duty trucks have coil-sprung Dana 60 front axles.
– The 2005 and newer F250, F350, F450, and F550 Super Duty trucks have Dana Super 60 front axles.
Please note that the Dana 60 front axle has been used in various Ford models, so it is always a good idea to verify the specific axle configuration for a particular Ford vehicle.

What vehicles did Dana Super 60 come in?

Ford used Dana Super 60 Front Driving Axles in 2005-2016 F250, F350, F450, and F550 Super Duty 4×4 trucks.

How do I identify my Ford Dana 60 front axle?

To find the complete build details of any Dana 60 axle, locate the BOM number stamped into the long axle tube and then find that code in the table below. Then, to find parts compatible with that axle, click on the link in the right column that will take you to the corresponding AxleBuilder.com page.

What vehicles came with a Dana 60 rear axle?

The Dana/Spicer 60 rear axle was used in 3/4 ton Dodge trucks from 1961 (or earlier), in 3/4 ton B-series vans, and in high- performance Dodge and Plymouth passenger cars beginning in 1966. Applications for the Dana 60 in Chrysler passenger cars were all Hemi and 440 cars with 4-speed manual transmission.

How do you identify a 1979 Ford Dana 60 front axle?

1978-1979 Dana 60 Front Axles in Ford Trucks had a Ford Axle Code Tag with the Ford Production Part Number and Dana Bill of Material Number (BOM) stamped on a metal Build Tag (red arrow) attached to the differential by two of the differential cover bolts (yellow arrows) when the vehicle was shipped from the factory but …

What trucks came with a Dana 60 front axle?

The Dana 60, a heavier-duty axle than the Dana 44, was first used in the 1950s. It was the axle of choice under countless Dodge, Ford, GM, Studebaker, IH and Jeep 3/4-ton and 1-ton fullsize trucks, as well as Ramchargers and Trail Dusters with the 440ci V-8, and some heavy-duty 1/2-ton Ford and IH trucks.

How do I identify my Ford Dana 60?

The best way to determine what axle model you have is to look at the axle ID tags. The Dana Axle Bill of Material Number will tell us what your axle model is, the ratio, and what parts your particular axle was built with. There should be a metal Dana BOM Tag held on by two of the diff cover bolts.

Are Ford and Dodge Dana 60 the same?

Dodge Dana 60s have an axle disconnect, which is considered a weaker and more complex axleshaft design. The split in the housing to accommodate the axle disconnect assembly is also considered weaker than the traditional one-piece axletube found on modern Ford Dana 60 axles.

How do I know if I have a Dana 50 or Dana 60 front axle?

now there’s a couple visual ways you can tell that you’re looking at a dana 50. 1st is there’s a very abrupt kick up in the casting on the dana 60. it’s a little more gradual. and the second is right here on the pinion.

How do you identify a Dana 60 year?

Each Dana 60 has a build date and bill of materials numbers stamped into the back of the passenger-side axle tube. These numbers are fairly small but they are always on original axles.

What years did Ford use Dana 60?

2005-2016 Ford Dana Super 60 Front Axle Identification IDN-118. Ford uses Dana Super 60 Front Driving Axles in 2005 and newer F250, F350, F450, and F550 Super Duty 4×4 trucks.