What tools do you need to change the brakes on a 2013 Ford Fusion?

Tools Needed to Change the Brakes on a 2013 Ford Fusion
To change the brakes on a 2013 Ford Fusion, you will need the following tools:
1. Jack and jack stands: These are necessary to safely lift and support the vehicle while working on the brakes.
2. Lug wrench: This is used to loosen and remove the lug nuts that secure the wheels.
3. C-clamp or brake caliper tool: This tool is needed to compress the brake caliper piston back into its housing, allowing for the installation of new brake pads.
4. Socket set: A socket set is required to remove the bolts that hold the brake caliper and bracket in place.
5. Torque wrench: This tool is used to tighten the lug nuts and other bolts to the manufacturer’s specified torque settings.
6. Brake cleaner: Brake cleaner is used to clean the brake caliper, rotor, and other brake components before installation.
7. Wire brush: A wire brush can be helpful for cleaning rust and debris from the brake caliper and bracket.
8. Brake grease: Brake grease is applied to the brake pad contact points and other moving parts to prevent noise and ensure smooth operation.
9. Safety glasses and gloves: It is important to wear safety glasses and gloves to protect yourself from any potential hazards while working on the brakes.
Please note that this is a general list of tools that are commonly used when changing brakes on a vehicle. The specific tools required may vary depending on the exact model and year of the Ford Fusion, as well as personal preference and the specific brake replacement procedure you choose to follow.
I hope this helps! Let me know if you have any other questions.

Do you have to put car in service mode for brakes?

This mainly depends on the manufacturer of the EPB, and the availability of a capable scan tool (if required) to enter the “service mode”, which most EPBs require before any work can be done on the brake(s) affected.

How long do Ford Fusion brakes last?

between 30,000 and 70,000 miles
Ford Fusion brake pads usually last between 30,000 and 70,000 miles depending on your driving habits. If you commute in heavy traffic and use your brakes often, you’ll need to get an inspection more frequently.

Are ceramic or metallic brakes better?

A set of ceramic pads will tend to last longer than metallic pads because they are harder and wear less. Very low amounts of brake dust. Ceramic brake pads create much less brake dust than an organic or metallic pad.

What tool is needed to change brakes?

Regardless of the make and model, the following are a few things I guarantee you’ll need; a good hydraulic jack, 2 Jack Stands, a Tire Iron or the appropriate sized socket and breaker bar. Those are the bare essentials needed for any brake pad/caliper replacement.

What size socket do I need to remove a brake caliper?

What size wrench do i need to take the front calipers off to replace my brake pads? Welcome and thank you for allowing me to assist you! to remove the caliper bolts from the bracket, you will need either a 13mm or 15mm socket wrench.

Do I need special tools to change brake pads?

As far as tools, you’ll want to round up a jack and jack stands, a lug wrench, C-clamp or caliper spreader tool, and a basic tool set. Many calipers require a Torx or Allen bit to remove the caliper bolts, so check to make sure that you have the correct tool before beginning the job.

How do you put a 2013 Ford Fusion in brake service mode?

At. The same time you’re gonna hold the accelerator pedal down to the floor. So you’re gonna hold them both down like this. And what you’re gonna do.

What kind of brakes does a 2013 Ford Fusion have?

At a basic level, cars like your Ford use what are called “friction” brakes. These brakes use the contact between two types of material to bring the car to a halt. A friction brake may be either a disc brake or a drum brake.

How much is a brake job for a Ford Fusion?

The average cost for a Ford Fusion Brake Pad Replacement is between $215 and $250. Labor costs are estimated between $87 and $109 while parts are priced between $128 and $141. This range does not include taxes and fees, and does not factor in your unique location. Related repairs may also be needed.

How do you put a Ford Fusion in brake maintenance mode?

So push it once and then within five seconds push it again. I can hear it re-engaging there in the. Back. Let’s make a whole bunch of noises back there. And now it is disengaged.