Rear Axle Size in Ford Excursion
The rear axle in a Ford Excursion is a Ford Sterling rear axle with a 10.5-inch ring gear. It has 3 pinion or spider gears between the side gears, designed to handle the torque of the vehicle.
This information is supported by the source: ‘Excursion axles | The Diesel Stop’.
If you need further assistance, feel free to ask!
Contents
- How do I identify my Ford Dana 80 rear axle?
- What size axle does my truck have?
- How do I know what size rear axle I have?
- What size is a rear axle?
- What is so special about a Ford 9 inch rear end?
- How do I identify my Ford rear axle?
- Where do I find my axle size?
- What size is the Dana 80 rear axle?
- How do I identify my Ford 9 inch rear axle?
- What trucks have a Dana 80 rear axle?
How do I identify my Ford Dana 80 rear axle?
It can be identified by its straight axle tubes, 10 bolt asymmetrical cover, and a “80” cast into the housing. Dana 80’s are made as full floating, rear axles only and are a step up in overall strength compared to the Dana 70.
What size axle does my truck have?
To figure out exactly what axle you have, you can look for the Dana stamped bill of materials number. This stamped number can usually be found on the righthand side or on the longer axletube on the same side of the tube as the differential cover, facing the rear of the truck.
How do I know what size rear axle I have?
To determine the axle ratio of your vehicle, locate the two-digit axle code first, then use your vehicle’s towing guide to find the axle ratio that corresponds to that code. If your vehicle has a limited-slip differential, it will be noted as “Limited Slip.”
What size is a rear axle?
Axle diameters of 15 millimetres at the front and 12 millimetres at the rear have become the established standards. On older bikes with a lot of suspension travel, 20-millimetre axles were sometimes installed at the front. Today, two axle diameters dominate the market, whether boost or non-Boost.
What is so special about a Ford 9 inch rear end?
One of the features which distinguishes this axle from other high-performance or heavy-duty domestic solid axles is that unlike other axle designs, access to the differential gears is not through the rear center cover; rather, in the Ford 9 inch, the rear cover is welded to the axle housing, and access to internals is …
How do I identify my Ford rear axle?
The ID tag can be your friend. It will tell you the gear ratio, rearend style, and whether it has limited-slip. Also on the tag is an ID number, which, until 1985, included four to five letters, no numbers. Almost all 8.8s—and all post-1986 Ford rearends—have letters and numbers.
Where do I find my axle size?
Usually this is located on the driver’s side of the trailer. Another way we can determine which axle we need is by measuring the diameter of the axle.
What size is the Dana 80 rear axle?
Heavy Hitter. The super-tough Dana 80 rear axle ranks as one of the most desirable axles for off-highway use. It’s a full-float unit with 11.25-inch ring gear diameter; 1.625-inch (minimum diameter) 37-spline pinion shaft; 11/2-inch-diameter, 35-spline axleshafts; and a 4-inch axletube diameter.
How do I identify my Ford 9 inch rear axle?
And this lip right here is for to to house the larger bearing you can see the same lip on my 75. Right here with the 11 inch rear drum.
What trucks have a Dana 80 rear axle?
Dana 80 Rear Axles have been in production since the 1988 Model Year. They have been used in Chevy/GMC 1992-2002 , Dodge(1994-2002), and Ford (1988-current) trucks vans, and motorhome chassis.
