What size is the axle nut on a 2nd generation dodge?

Based on the search results, the size of the axle nut on a 2nd generation Dodge Ram varies depending on the specific model and year. Here are the findings:
– According to a post on DodgeForum.com, some users mentioned that the front axle nut size for a 2nd generation Dodge Ram is 1 11/16″.
– Another post on Dodge Diesel – Diesel Truck Resource Forums mentioned that the front hub nut size for a 1997 Dodge Ram 2500 is 175 ft lbs and an impact socket of that size worked well.
– A post on Turbo Diesel Register mentioned that the axle hub nut size for a 2nd generation Dodge Ram is unknown.
– A post on DodgeForum.com mentioned that the axle nut size for a 1997 Dodge Ram 1500 4×4 is 1-11/16″ or 43mm.
– According to an article on DodgeForum.com, the axle nut size for a Dodge Ram 1500 from 1994 to 2002 was 1″ or 43mm. However, if the axle has been replaced with an aftermarket product, the nut size can be 36mm.
– A post on DodgeIntrepid.Net Forums mentioned that the axle hub nut size for a Dodge Intrepid is unknown.
– Another post on DodgeForum.com mentioned that the axle nut size for a Dodge Ram 1500 is 36mm.
– A post on Turbo Diesel Register mentioned that the hub nut size for a 2nd generation Dodge Ram is unknown.
Based on these search results, it seems that the axle nut size on a 2nd generation Dodge Ram can vary. It is recommended to consult the vehicle’s manual or contact a Dodge dealership for the specific axle nut size for your particular model and year.

What front axle is in a 2001 dodge 2500?

Dodge Ram 2500 and Dodge Ram 3500 4×4 trucks for the model years of 2000, 2001, and 2002 all use Dana-Spicer Model 60 248 Front Beam Iron (FBI) drive axles. Outwardly, these solid beam axles look very similar to the preceding models; however, relatively few parts were carried over from the 1999 and prior axles.

What size is the axle nut on a 2007 Dodge 2500?

The axle nuts on a 2007 Dodge Ram 2500 typically require a 1-11/16 inch socket to remove. As this is an obscure size, it’s typically also possible to use A43mm socket, but this is of course not recommended.

What size socket is the axle nut on a 2004 dodge 2500?

Remove spindle nut with a 1 11/16 in socket.

What size socket is the axle nut for a 2001 Dodge Ram 1500?

The axle nut on the 2001 dodge ram 1500 is 1 11/16 inches.

What size is the axle nut on a 2000 Dodge Ram 1500?

The Dodge Ram 1500 truck has an axle nut size of 36 mm. This is also measured aS3/16 to 3/18 of an inch. You will need a 30 mm 12 point axle nut socket wrench to apply and remove the axle nuts from Your vehicle.

What axle is in a 2000 Dodge Ram 1500?

The Dana-Spicer, Model 44 216 Front Beam-Design Iron (FBI) axle was used on all 1994 to 2001 Ram 1500 4×4 1/2 Ton trucks and 1994-1997 gas V8 powered, light duty Ram 2500 trucks with Gross Vehicle Weights (GVW) under 8800 pounds.

What size is the front axle nut on a dodge 2500?

its 43mm as I recall when converting to locking hubs.

What size is the rear axle nut on a dodge 2500?

The axle nut size for modern Dodge Ram 2500 trucks will be 46mm. When You are adding or removing the lug nuts from a car then You will want to be careful not to damage them. If You overtighten them then You run the risk of snapping them or stripping them, especially if they are old or rusted.

What size is the axle nut on a 2007 dodge 2500?

The axle nuts on a 2007 Dodge Ram 2500 typically require a 1-11/16 inch socket to remove. As this is an obscure size, it’s typically also possible to use A43mm socket, but this is of course not recommended.

What size are the wheel nuts on a Dodge Ram 2500?

Wheel Nut M14-1.50 Metric – 22mm Hex – 26mm Length.