Axle Nut Size for a 2011 Chevy Cruze
The axle nut size for a 2011 Chevy Cruze is 32mm. This is the size needed for the axle nut when working on the wheel hub and brakes of the vehicle.
Additionally, it’s important to note that the torque specifications for the axle nut tightening are as follows:
– First, tighten to 111 ft-lbs/150 Nm
– Second, loosen by 45 degrees
– Lastly, tighten to 185 ft-lbs/250 Nm.
Contents
- What size is the axle nut on a Chevy Cruze?
- What size socket do I need for wheel nuts?
- What is the torque on the axle nut on a Chevy Cruze?
- What size is the axle nut bolt?
- What size socket do you need for a CV axle?
- What can I use to remove an axle nut?
- What size is the axle nut on a CV axle?
- Do you need a torque wrench for axle nut?
- What size socket do I need to remove an axle nut?
- What size bolt is on a CV axle?
What size is the axle nut on a Chevy Cruze?
SPECIFICS:
| Abs Ring Tooth Count | N/A |
|---|---|
| Axle Nut Length (in) | 1 1/2 |
| Axle Nut Length (mm) | 37 |
| Axle Nut Locking Type | Self-Lock |
| Axle Nut Thread Size | M22*1.5 |
What size socket do I need for wheel nuts?
If the question “what size of sockets for lug nuts should I use” comes to your mind; the most common socket sizes for lug nuts are 17 mm, 19 mm, 21 mm, and 22 mm, all available at Olsa Tools.
What is the torque on the axle nut on a Chevy Cruze?
Notes: 33 spline hub. Axle nut torque: tighten to 111 lb ft (150 Nm), back nut off 45�, final tighten to 184 lb ft (250 Nm). Quantity per car: 2.
What size is the axle nut bolt?
36mm Axle Nut Socket – services many GM, Ford and Chrysler full-size vehicles. 32mm Axle Nut Socket – services late model Honda and Chrysler vehicles. 34mm Axle Nut Socket – services many GM mid-size vehicles. 29mm Axle Nut Socket – services late model GM, Ford and Asian imports.
What size socket do you need for a CV axle?
36mm is correct. Make sure it’s attached to a decent breaker bar; those things are on there pretty tight.
What can I use to remove an axle nut?
Go ahead and get your wheel and pop the center cap. Off. Go ahead and put the wheel back on and lower down the vehicle.
What size is the axle nut on a CV axle?
The stock one should thread on fine though so you can just reuse it if you don’t want to buy a second socket. OEM is 35mm, most aftermarket are 36mm.
Do you need a torque wrench for axle nut?
And the outer race of that wheel bearing in other words the preload. If. It’s not set properly well. You’re gonna have premature bearing wear and it’s gonna fail a lot sooner than it would naturally.
What size socket do I need to remove an axle nut?
There is several different sizes that the axle nut could be most axle nut sets will have sockets from 28mm-38mm. The more common ones are 32-36. You may see if the new axle you are installing has a new nut which is recommended when replacing and use that to match up if you just want to buy a single socket.
What size bolt is on a CV axle?
As you have found, it is a M10X1. 5X25 grade 10.9 bolt.
