Stock Injector Size on a Ford Lightning
Based on the search results, the stock injector size on a Ford Lightning can vary depending on the specific model and year. Here are the findings:
– 2nd Generation Lightning: According to a forum post on SVTPerformance.com, the stock injector size for a 2nd generation Ford Lightning is 42 lb/hr.
– 1990 F150 XLT LARIET 4X4: In a forum post on Ford Truck Enthusiasts Forums, it is mentioned that the stock injectors for a 1990 F150 XLT LARIET 4X4 with a 302 engine are 19 lb/hr.
– 2000 Lightning: Another forum post on Mod Motor Tech Forums states that the stock injector size for a 2000 Ford Lightning is 42 lb/hr.
– 1999-2004 SVT Lightning: Late Model Restoration, an online retailer, offers 47 lb/hr fuel injectors as a stock replacement for unmodified trucks. However, it’s worth noting that upgrading to larger injectors may require a tune to ensure proper engine performance.
Please keep in mind that these findings are based on user discussions and may not be exhaustive or applicable to all Ford Lightning models. It is always recommended to consult with a trusted mechanic or refer to the vehicle’s official documentation for accurate information about stock injector sizes.
Contents
- What are the specs of the Ford Lightning engine?
- How many cc are 80lb injectors?
- What size injectors do I need for 300 hp?
- What engine did the Ford Lightning come with?
- What size are common rail injectors?
- Does the Ford Lightning have a Triton engine?
- What is the size of a standard injector?
- What size injectors do I need for 500hp?
- How much HP will 30 lb injectors support?
- How do you tell injector size?
What are the specs of the Ford Lightning engine?
Ford F-150 Lightning Features
It was designed with serious power and impressive capability. Twin electric motors generate 563 horsepower and 775 lb-ft of torque, sent to all four wheels through a pair of electric motors.
How many cc are 80lb injectors?
fit Deka Siemens , Reliable Injectors. Standard Long Length 60mm 0-ring to o-ring. Static flow rate : 80lb/hr = 850 cc/min.
What size injectors do I need for 300 hp?
Flow Rate Definition, Calculating and Horsepower Range
| Injector Flow Rate | Naturally Aspirated Engine | Engine w/ Power Adder |
|---|---|---|
| 24 lbs./hr. | 280-360 hp | 240-300 hp |
| 30 lbs./hr. | 350-450 hp | 300-375 hp |
| 36 lbs./hr. | 425-540 hp | 350-450 hp |
| 42 lbs./hr. | 500-625 hp | 410-525 hp |
What engine did the Ford Lightning come with?
2nd Generation SVT Lightning: Performance
While the 1999 and 2000 models were equipped with a 5.4L Eaton-Supercharged V8 that produces 360 HP, the engine was later tuned to provide 380 horsepower 450 lb-ft of torque from the 2000 Model Year and onwards.
What size are common rail injectors?
Table 1.
| Item | Unit | Value |
|---|---|---|
| Diameter of hole ( D ) | mm | 0.124 |
| Length of hole ( L n ) | mm | 0.756 |
| Diameter of SAC ( D s ) | mm | 0.44 |
| Diameter of needle seat ( D s t ) | mm | 0.94 |
Does the Ford Lightning have a Triton engine?
To this end, they further developed the 5.4L Triton V8, equipping it with an intercooled Eaton Gen IV supercharger and performance cooling system. The tuned powerplant produced 360 horsepower right out of the gate, transferred through a modified 4R100 4-speed automatic.
What is the size of a standard injector?
Typically injectors come in three sizes; 34, 48 and 60mm. These measurements are taken from the top of the lower O-ring to the bottom of the upper O-ring. Pictured below are three common injector types/sizes; (L to R) ID850/1300/2000 (34mm), ID725/1000 (48mm), EV1 Bosch 1680 (60mm).
What size injectors do I need for 500hp?
Calculating injector size for a 500 horsepower normally aspirated engine on E85, we would use the 0.70 BSFC number. Including a maximum 70 percent duty cycle, this would put the injector size at 57 to 60 lbs/hr compared to gasoline’s 42 lb/hr size.
How much HP will 30 lb injectors support?
#30 are good for over 400 whp.
How do you tell injector size?
When sizing your injector for gasoline a very simple rule of thumb to follow is: 1cc/min flow for each horsepower. So, if you want to make 1000 crank horsepower on 93 octane gasoline, using a fuel pressure of 43psi you need a 1000cc injector. This rule of thumb can be used for ethanol based fuels like e85.
