What rear end is in a Chevy S10?

Rear End in a Chevy S10
The rear end in a Chevy S10 can vary depending on the specific model and year. However, based on the information from the search results, it appears that the most common rear end options for the Chevy S10 include the following:
1. 7.5-inch Rear End:
– The 7.5-inch rear end was standard until 1993, and it has 26 splines or grooves.
– The original inspection plate on the 7.5-inch rear end has a drain plug on the lower passenger side.
2. 7.625-inch Rear End:
– The 7.625-inch rear end became standard in 1993, replacing the 7.5-inch rear end.
– It has 28 splines or grooves.
3. Currie Ford 9-inch Rear End:
– Currie Enterprises offers a complete, ready-to-bolt-in Currie 9-inch rear end for 1982 thru 1997 Chevy S-10/Blazer and GMC S-15/Jimmy 2WD trucks and SUVs.
4. Other Options:
– The S10/Sonoma 7.5/7.625″ rear axle is a good choice for small lightweight hot rods such as T-Buckets or early roadsters.
– The 2WD version of the S10 rear end is the right length to go under certain vehicles.
It’s important to note that the rear end in a Chevy S10 can have various configurations and options, including upgrades and modifications available from aftermarket manufacturers like Currie Enterprises. If you have a specific Chevy S10 model or year in mind, it’s advisable to consult with a professional or refer to the vehicle’s documentation for precise information.

What is the strongest Chevy rear end?

Chevrolet 12-bolt rear
The Chevrolet 12-bolt rear axle is a prolific piece. It turns up in countless Camaros, Chevelles, Novas and full size Chevys. Although it may not be as popular as a 9-inch Ford in drag race applications, the 12-bolt does have a number of plusses (not the least of which is decent strength when carefully prepped).

How wide is a stock S10 rear end?

2 wheel drive S-10’s, pickup and blazer use a rear axle that is 54″ wide. The 4×4’s have a wider axle, but I can’t remember exactly how much wider they are… sorry. If you don’t mind running a ford rear axle check out one from a Ford Explorer. 1995 and newer, they use the 8.8″ rear and measure 60″ wide.

Is a GM 10 bolt rear end good?

Chances are good your 10-bolt rear axle has sluggish grocery getter gears, which means your Chevelle, Camaro, or Nova suffers from anemic performance. Those 2.73:1 cogs are good for the open highway with a non-overdrive automatic or classic four-speed.

What size is a Chevy 10 bolt rear end?

Many times, if you locate a 10-bolt rearend, it’s usually a 7.5-inch unit. These have been around since 1975, and were installed under cars, small trucks, and vans up to the 2005 model year.

What size rear end is a 95 S10?

I had read that ’95 and newer s10 4.3 V6 equipped S10’s had the stronger 8.5″ 10 bolt rear ends. The overall width varied depending on 2 or 4wd.

How do you tell if you have a 8.2 or 8.5 rear end?

Will look over here on. The. Eight point two three ran out of a Monte Carlo. And you can see. There is no ears on the bottom.

What year S10 has a 8.5 rear end?

Out. If you have a pickup or a two-door blazer. And it has the l35 4.3. And a manual transmission it has an eight and a half inch rear.

What did Chevy 10 bolt rear end come in?

You can find a 10-bolt 8.5-inch differential in any of these cars or trucks: 1970-’81 Chevrolet Camaro. 1970-’81 Pontiac Firebird. 1971-’76 Chevrolet Impala and Caprice.

How wide is the rear end of the S10 4×4?

2wd is ~54″, 4×4 is ~59″. there is a Zr2 that is wider still ~63, but may look too wide if you dont have big spacers on the front.

How do I know if I have a 7.5 or 8.5 rear end?

You can tell them apart by the diff cover. It is hard to explain, and I wish I had a picture to show you the difference. The 7.5″ has an overall shape of a square with round corners, whereas the 8.5″, the raised section almost resembles a football.