What oil should I use for my Dodge Dakota?

Oil Recommendation for Dodge Dakota
For your Dodge Dakota, the recommended engine oil is 5W-30 or 10W-30. The best option comes down to the type of motor oil, and between conventional oil and synthetic oil, full synthetic or synthetic blends are the best choice. It’s important to note that the Dodge Dakota was manufactured over many years, so it’s advisable to use the filter above to narrow down your options by year, make, model, and engine size.
Engine Oil Change Intervals
The engine oil should be changed at regular intervals, and the oil filter must be replaced every time the oil is changed, unless the car’s owner’s manual recommends otherwise.
High Mileage Engine
For a high mileage engine, some users have reported using 0W-20 and found it to perform well in torture tests, with no discernible difference in engine wear compared to 5W-30. However, it’s important to note that the manual specified 5W-30 for earlier models, but this changed to 5W-20 on later models, although tolerances stayed the same.
Specific Recommendations
It’s also mentioned that the best type of engine oil to use is synthetic, and the specific engine oil quality for your Dakota can be found in the owner’s manual.
User Recommendations
Some users have reported using 10W-30 and 10W-30 Pennzoil High Mileage for their Dodge Dakota without any problems with oil consumption. Others have used a mix of 5W-30 and 10W-30 synthetic oils, and have considered switching back to conventional oil at some point.
It’s important to consider the specific requirements for your vehicle based on its year, make, model, and engine size, and to consult the owner’s manual for the most accurate and up-to-date information.

What oil does a Dodge Dakota V6 take?

Oil Grade: API*

Viscosity:	Below 0 C .5W-30 Above -18 C .10W-30 – SAE 10W-30 is preferred.
Capacity:	With filter 3.8 litres. After refill check oil level.
Torque:	Oil Drain Plug…25 ft/lbs

What kind of oil does a Dodge Dakota 3.9 L v6 take?

SAE 10W-30
Oil Grade: API*
10W-30 (Above -18) – SAE 10W-30 is preferred.

What oil does a Dodge Dakota v6 take?

Oil Grade: API*

Viscosity:	Below 0 C .5W-30 Above -18 C .10W-30 – SAE 10W-30 is preferred.
Capacity:	With filter 3.8 litres. After refill check oil level.
Torque:	Oil Drain Plug…25 ft/lbs

What kind of oil does a 95 Dodge Dakota 3.9 take?

CRAFTSMAN 10W-30 Full Synthetic Automotive Engine Oil is designed for maximum protection of your gasoline engine.

Can I put 5w30 instead of 5w20?

Using 5W-30 instead can reduce fuel economy and impede flow throughout the engine. While using it temporarily in a pinch likely won’t cause your engine lasting harm, remember that the engineers who built your engine did so with a specific viscosity oil in mind, meaning it’s best to stick with it.

What type of oil does a 2000 Dodge Dakota with a v6 take?

Notes: Full synthetic. 5W-30.

What oil does Dodge recommend?

Pennzoil synthetic oil does NOT void the warranty of your Chrysler, Jeep, Dodge, or Ram and in fact Pennzoil synthetic is the recommended oil in all their vehicles.

What oil does a Dodge 3.6 L take?

The 3.6L Pentastar® V6 engine takes a synthetic blend oil. It’s preferred that you use one with an oil weight of SAE 0W-20. If you’ve got the 5.7L HEMI® engine, however, you’ll want to use synthetic oil that’s got a weight of SAE 5W-20.

What oil does a 2003 Dodge Dakota 3.9 L take?

SAE 10W-30
Oil Grade: API*

Viscosity:	10W-30 (Above -18) – SAE 10W-30 is preferred. 5W-30 (Below 0)
Capacity:	4 quarts (with filter). After refill check oil level.
Torque:	25 ft/lbs (Oil Drain Plug)

Can I use 5W-30 instead of 5w20 in my Dodge?

As long as the manual says 5w-30 is ok to use, is a suitable alternative if 5w-20 not available, the engine is ok. That makes sense. I’ll ask just out of curiosity, but the manual says it’s an acceptable alternative.