The torque specifications for the brake calipers on a 2005 Dodge Magnum are as follows:
– Front brake caliper bracket: 70 ft/lbs
– Rear brake caliper bracket: 85 ft/lbs
– Caliper bolts: 44 ft/lbs for the front and 23 ft/lbs for the rear
Please note that these torque specifications are specific to the 2005 Dodge Magnum and may vary for different models or years. It is always recommended to consult the vehicle’s owner manual or a trusted source for the most accurate and up-to-date information.
Contents
- How tight do brake caliper bolts need to be?
- Should you torque brake calipers?
- What is torque spec for lug nuts?
- Should I use Loctite on my brake caliper bolts?
- What is the torque on brake caliper mounting bolts?
- Should you put anti seize on caliper bolts?
- What is the brake torque?
- What torque for disc brake calipers?
- What are torque specifications?
- How tight should disc brakes be?
How tight do brake caliper bolts need to be?
The caliper retaining bolts are the big ones that hold the main body of the caliper to the hub assembly. They are quite big, often 15–19mm bolts and take a fair effort to crack them off. These require tightening to 80 plus lbs ft or in general, as tight as you can get them with a 1/2 inch socket set ratchet.
Should you torque brake calipers?
Do brake caliper bolts need to be torqued? It would be a good idea – calipers serve a very important function and you don’t want them coming loose. That said I have done many of them (in the past) without a torque wrench but not anymore.
What is torque spec for lug nuts?
Under- or over-tightening wheel-attaching hardware can be damaging and dangerous.
| Hardware Bolt or Stud Size | Typical Torque Range in Ft/Lbs | Minimum Number of Turns of Hardware Engagement |
|---|---|---|
| 12 x 1.25 mm | 70 – 80 | 8 |
| 14 x 1.5 mm | 85 – 90 | 7.5 |
| 14 x 1.25 mm | 85 – 90 | 9 |
| 7/16 in. | 70 – 80 | 9 |
Should I use Loctite on my brake caliper bolts?
The caliper bolts & guide pin mounting screws need to have the medium strength (blue) loctite applied to the threads !
What is the torque on brake caliper mounting bolts?
Brake caliper bracket bolts connect the caliper bracket to the spindle or knuckle, never seen one with any kind of sleeve. Usually torqued to 80+ ft lbs, big bolts that usually use a 20+mm or 5/8 or larger socket.
Should you put anti seize on caliper bolts?
No anti-seize required. The steel caliper bolts screws into the aluminum carrier. Anytime you mate steel and aluminum, you should use anti-seize to prevent corrosion and galling the threads.
What is the brake torque?
Brake torque is essentially the power of the braking system. The brake caliper acts on the disc at a certain distance from the hub center, known as the effective radius. The force exerted by the caliper, multiplied by the effective radius of the system equals the brake torque.
What torque for disc brake calipers?
required position and then tighten the two caliper fixing bolts alternately by small amounts each time. Tightening torque: 6 – 8 N·m {53 – 69 in. lbs.} or three clicks.
What are torque specifications?
When attaching a wheel to a vehicle, torque specifications are the amount of force recommended on the hardware to ensure proper installation. Following exact torque specifications matters for a number of reasons. Too much torque can result in overtightening, which has significant consequences.
How tight should disc brakes be?
Key to tighten each of the bolts up correctly. Now the torque setting for these is around eight newton meters. But you just need to ensure that they’re tight. So there’s no risk of the caliper.
