The torque on the strut bolts of a Toyota Corolla can vary depending on the specific model and year. However, based on the search results, here are some torque specifications for the strut bolts on different Toyota Corolla models:
– For a 2003 Toyota Corolla 1.8, the strut bolts should be torqued to 166 ft-lb.
– For a 2009 Toyota Corolla S, the torque specifications are as follows:
– Front shock absorber nut x Piston rod: 35 ft-lb
– Three bearing plate nuts for the front strut: 29 ft-lb.
– For a 1990 Toyota Corolla DX sedan, the torque specs for the bolts are not available. However, it is recommended to replace the entire assembly.
– For a Toyota Corolla rear strut, the strut-to-arm bolt should be torqued to 188 ft-lb.
Please note that these torque specifications are based on the information provided in the search results. It is always recommended to consult the specific vehicle’s manual or reach out to a certified technician for the most accurate and up-to-date torque specifications for your Toyota Corolla model.
Contents
- What is a torque strut mount?
- How do you torque a strut nut?
- What should struts be torqued to?
- How tight should a top strut nut be?
- What should axle nuts be torqued to?
- Do I need a torque wrench for struts?
- What is the torque on the axle nut of a 2010 Toyota Corolla?
- How much torque does a 2009 Toyota Corolla front axle nut have?
- What is the torque spec for the rear struts on a 2004 Camry?
- Do you need a torque wrench when replacing a strut on a car?
What is a torque strut mount?
A torque strut mount stabilizes your engine’s position in relation to the chassis. It keeps everything steady while the engine is trying to torque over when the vehicle runs or stops. In short, it lessens the effect of engine torque on your ride’s stability.
How do you torque a strut nut?
There we’re going to pulse. This so that it goes. On you see my hand. I can’t hold. That because it’s an impact gun it’ll turn the nut faster than the shaft. It’s still not tight.
What should struts be torqued to?
On re-install, the lower of the two nuts on the strut top should be torqued to 58 ft/lb before the strut goes in the car. Once in the car, install the upper top strut nut, but don’t torque it yet. Install the strut to knuckle bolts.
How tight should a top strut nut be?
You should leave them just about snug, if not just a little loose. If you tighten them before you put it on the ground, when you do get the car on the ground, there will be tension on the parts, which means it will wear quicker. So, leave them a little loose, then tighten once on the ground …
What should axle nuts be torqued to?
The nut holds just the axle in the hub and to the flange. With these types of hub units, they typically have lower axle nut torque specifications that can be between 85- and 170-ft. lbs. The torque specification can also vary due to the diameter and size of the rolling elements.
Do I need a torque wrench for struts?
This spring re-vamp is getting more and more expensive! Yes. The torque wrench is only required when you are re-installing the upper strut bolts, the bolts on top of the strut. If you do not have a torque wrench, just use a ratchet and snug the bolts tight, but do not over tighten.
What is the torque on the axle nut of a 2010 Toyota Corolla?
The front axle nut torque specification is 158 FT/LBS.
How much torque does a 2009 Toyota Corolla front axle nut have?
Front Axle Nut
Torque: 159 ft.
What is the torque spec for the rear struts on a 2004 Camry?
The rear suspension strut-to-axle carrier nuts/bolts (19mm) have a torque spec of 188 ft. lbs. in an official 2004 Camry Repair online manual.
Do you need a torque wrench when replacing a strut on a car?
Installing New Shocks and Struts
Make sure that you tighten all of the bolts securely. You will probably need a torque wrench to do this. Put the wheels back on the vehicle and you’re ready to test it out.
