Torque Specifications for Model A Ford Head Bolts
The torque specifications for Model A Ford head bolts are as follows:
– The long accepted standard for a stock head is 55 lb-ft, and as much as 65 lb-ft for a 6:1 high compression head.
– It is recommended to initially torque the head in three passes following a sequence, going from 35 to 45 to 55 lb-ft. After some running and cool down cycles, re-torque to 55 lb-ft again because the gasket will take some compression and will lose some torque after initial use.
It’s important to follow the recommended torque sequence and values to ensure proper installation and performance of the cylinder head bolts.
If you have any further questions or need additional information, feel free to ask!
Contents
- What are the torque specifications?
- Where can I find torque specs?
- How much torque does a Model A have?
- Should you torque the head of a bolt or nut?
- What are the torque specs on a Ford?
- What is the torque on the Model A Ford head?
- Do I need a torque wrench for head bolts?
- What is the head bolt torque on a 302 Ford?
- What is the torque sequence for head bolts?
- Should a torque wrench be used to tighten head bolts?
What are the torque specifications?
Torque specifications are the values that indicate how much force should be applied to a bolt. These values are usually given in Newton meters (Nm) or foot-pounds (ft-lbs). Torque specifications are essential because they ensure that bolts are tightened to the correct level.
Where can I find torque specs?
Torque specs are published in service manuals. When a torque spec is not listed every bolt of a said size and strength has a general torque to value as well as a yield range.
How much torque does a Model A have?
Ford Model A engine | |
---|---|
Torque output | 128 lb⋅ft (174 N⋅m) at 1,000 RPM |
Dimensions | |
Dry weight | approx. 350 lb (160 kg) with radiator and water |
Chronology |
Should you torque the head of a bolt or nut?
There is no simple answer to this as in some instances, it is perfectly acceptable to tighten the bolt head while holding the nut in place. In other situations, it’s acceptable to tighten the nut. It all depends on the application and the condition of the product or material being worked with.
What are the torque specs on a Ford?
Ford Engine Bolt Torque Chart
Fastener Type | Torque Spec |
---|---|
Connecting rod bolts | 40-45 ft-lbs. |
Cylinder head bolts | 90-100 ft-lbs. |
Rocker arms | 17-23 ft-lbs. |
Intake manifold bolts | 23-25 ft-lbs. |
What is the torque on the Model A Ford head?
Re: Model A Head Bolt Tightening
Use your torque wrench to remove the nut, and with the dial set to click at 55 pounds of torque. If you initially torqued the nut to 55 pounds and have run the engine up to operating temps, allow it to cool to room temperature before you check anything.
Do I need a torque wrench for head bolts?
If you plan to do any major work on your engine or on some major powertrain components, you absolutely need a torque wrench. Overtightening cylinder-head bolts, for instance, can easily cause expensive damage and catastrophic coolant loss.
What is the head bolt torque on a 302 Ford?
Ford Windsor 289, 302, 351 Torque Specs.
Fastener Type | Torque Specs |
---|---|
Connecting Rod Bolts | 22-25 ft.-lbs. (40-45 ft.-lbs. for 289TP and Boss 302) |
Cylinder Head Bolts | 65-72 ft.-lbs. |
Rocker Arms | 17-23 ft.-lbs. |
Intake Manifold Bolts | 23-25 ft.-lbs. |
What is the torque sequence for head bolts?
Generally speaking, cylinder head bolts are torqued in a series of passes, usually at least 3 from the condition of just tight to that of tightened to final torque, in an ever-increasing circular pattern from the center outward toward each end.
Should a torque wrench be used to tighten head bolts?
Each vehicle type has different torque specifications, set by the manufacturer, which must be respected when servicing the vehicle. Not only for the wheels, but also for any other bolted parts such as the cylinder head, a torque controlled solution must be used to tighten at the required torque.