What is the rear axle ratio of a 2006 Ford f450?

Rear Axle Ratio of a 2006 Ford F450
The rear axle ratio of a 2006 Ford F450 can be determined from the axle code found on the vehicle’s door sticker. The axle code is typically located in the area labeled (F) on the door jamb sticker. Here are some examples of axle codes and their corresponding gear ratios:
– Axle Code: 26
– Gear Ratio: 3.73
– Limited Slip: Non-limited slip for an F150.
– Axle Code: C3
– Gear Ratio: Not specified in the provided search results.
– Axle Code: 35
– Gear Ratio: Not specified in the provided search results.
– Axle Code: RC 47
– Gear Ratio: Not specified in the provided search results.
– Axle Code: 31
– Gear Ratio: Not specified in the provided search results.
It’s important to note that the axle code may vary based on the specific model and configuration of the vehicle. For accurate information regarding the rear axle ratio of a 2006 Ford F450, it is recommended to refer to the vehicle’s door sticker or consult a certified Ford dealership for precise details.
If you have any further questions or need additional assistance, feel free to ask!

What is a 3.73 rear axle ratio?

Axle Ratio Explained
It represents the number of revolutions the driveshaft must make to rotate the axle one full cycle. It is rendered in a ratio such as 3.73. 1 or 3.73. So if a truck has an axle ratio of 3.73:1 or 3.73, it means the driveshaft turns 3.73 times to spin the axle one full cycle.

What is the difference between 3.55 and 3.73 axle ratio?

1:3.73 is about 5% lower than 1:3.55. So if you change from 3.55 to 3.73 , you’re going 5% slower when you hit the same gear change – if you normally change first to second at 30 mph, now you change at 28.5 mph, second to third at 50 mph -> now at 47.5 mph, etc.

What is the best gear ratio for a 4wd?

The ratios from first to fifth gear are 6.16, 3.11, 1.71, 1.00 and 0.76. The 6.16 ratio gives you acceleration for standing starts and torque for crawling or steep hills. The 0.76 ratio is ideal for highway cruising.

What is the best gear ratio for 4×4?

Not all gear ratios are available so you have the choice between 4.88 and 5.13, 4.88 being the closest. Choose a little bit lower gear ratios if you do a lot of off-road driving and a little bit higher if you do more long distance highway trips. For calculating this formula on-line go to the Tire Size Calculator.

Is a 3.55 axle ratio good for towing?

The higher the ratio, the more revolutions per minute. Towing: For pickup trucks released after 2010, the best axle ratio for towing falls somewhere between 3.55 and 3.73. This range provides good acceleration for V8 gas and diesel engines.

What is the rear axle ratio of a 2016 Ford f450?

4.30
2011 2012 2013 2014 2015 2016 Ford F-450 F-550 Super Duty Rear Differential Axle Gear Ratio 4.30.

How do I find my Ford axle ratio?

To find the axle code:

1. View the Safety Compliance Certification Label on the driver’s side, front or rear door panel.
2. Find the word “AXLE” under the bar code.
3. Find the two-digit code under “AXLE.”

What is the rear axle ratio of a 2008 f450?

The 2008 f-450 and f-550 were available with 4.30:1 or 4.88:1 rear ratios.

What is the gear ratio of the F-450?

Ford F-450 Compression and Gear Ratios
First: 4.615 to 1. Second: 2.919 to 1. Third: 2.132 to 1.

Should I get 3.73 or 4.10 gears?

There is only a 10% difference between 4.10 and 3.73 gears. Unless you need to tow heavy loads, I would keep the 3.73 gears. Or maybe if you are going to big, big tires. Otherwise you probably won’t notice the difference.