What is the difference between Ford and Holden bearings?

Difference Between Ford and Holden Bearings
The main differences between Ford and Holden trailer bearings are related to their sizing and compatibility with specific axles and hubs. Here are the key distinctions:
1. Sizing and Axle Compatibility:
– Ford bearings, also known as slimline bearings, are rated for 1500 kg on a 45 mm round or square axle, while Holden bearings (LM) are rated for 750 kg on a 39 mm round or 40 mm square axle.
– The inner bearing is larger than the outer with standard bearings, but with parallel bearings, they are the same size.
– Ford hubs are 68mm from stud to stud, Holden HT/Early Holden hubs are 65mm from stud to stud, and Holden HQ hubs are 72mm from stud to stud.
– The thread diameter of the wheel studs is different between Holden and Ford, with Holden hubs using 7/16 inch UNF nuts and Ford hubs using 1/2 inch UNF nuts, with a different hex size.
2. Identification:
– One quick way to check the hub is to measure from the center of one wheel stud to the center of the next, as the measurements vary for Ford and Holden hubs.
– Additionally, the size of the hex and the thread diameter of the wheel studs can be used to differentiate between Ford and Holden hubs.
3. Compatibility with Trailers:
– Most caravans and trailers use either Holden or Ford bearings, while some large and off-road ones use parallel bearing sets.
– It’s important to note that the axle determines the bearing size, and they must be rated correctly for the weight being hauled.
In summary, the differences between Ford and Holden trailer bearings primarily lie in their sizing, axle compatibility, and specific identification methods for each type of bearing.
If you have any further questions or need additional information, feel free to ask!

How do you tell if a trailer has Holden and Ford bearings?

The Holden hammers are 11 millimeters. Okay and there’s the two main differences between the four the whole house. And. So hopefully that they please that up for you makes it real simple.

How can you tell the difference between a Ford and Holden stud pattern?

The thread diameter of the wheel studs is different between Holden and Ford, I find this the quickest and easiest way to tell them apart. The Holden hub runs 7/16 inch UNF nuts whilst the Ford hub runs 1/2 inch UNF nuts, and the size of the hex is different (bigger on FOrd pattern).

Can you put Ford bearings in a Holden hub?

Holden bearings have a smaller inner diameter on each bearing than the Ford bearings, hence the Holden axle stubs are machined to smaller diameters. The axle stub determines the required bearing. The hubs or disks will fit either type of bearing.

Do Ford wheels fit Holden?

If the size between the studs was the same on all of them, the PCD would be the same and then they would all fit each other except for the stud size on the ford. Ford, Early Holden, Late Holden and Commodore are all different measurements so they are not the same on all of them. Also Volvo fit Early Holden and Torana.

How can you tell the difference between Holden and Ford hubs?

The Holden hammers are 11 millimeters. Okay and there’s the two main differences between the four the whole house. And. So hopefully that they please that up for you makes it real simple.

What size is the seal on a Holden bearing?

Standard Holden Bearing Seal
Standard holden LM grease seal, ID 37.5mm, OD 59.10mm.

What is the difference between Ford hub and Holden hub?

2) In most cases, Holden studs are 5/16inch whilst Ford are 1/2inch, but whilst rare you can get Ford hubs with 5/16inch studs, 3) If your axle size is 39mm round or 40mm square you should have Holden type bearings. If the axle is 50mm square they should be Ford type bearings.

Are all trailer bearings the same?

The hub holds 2 bearings, the inner bearing (inside the hub flange, closest to the trailer center), and the outer bearing. Since one size trailer wheel bearing does not fit all, to determine the correct size wheel bearing for your trailer, you’ll have to take apart the hub.

What size are Holden bearings?

LM (Holden bearings) are rated for 750Kg on a 39mm round axle or 1000Kg on a 40mm square axle. Timken LM bearing kit includes: 1 x Set 6 bearing – 67048 cone & 67010 cup (67048/10) 1 x Set 2 bearing – 11949 cone & 11910 cup (11949/10)

Are Ford and Holden bearings interchangeable?

The safest way to ensure that you get the right ones for your trailer is to check the numbers on the side of the inner and outer bearings and order the same ones. Just measure the axle or stub axle behind the wheel. If it is 40mm square or round it runs holden bearings, if it is 45mm square it will run ford bearings.