The code P0446 on a Toyota Echo indicates an Evaporative Emission Control (EVAP) system vent control circuit malfunction. This code is often triggered along with other related EVAP codes, such as P0441, and the combination of codes can help pinpoint the actual problem.
The EVAP vent control valve in the Toyota Echo is responsible for regulating and maintaining pressure in the fuel tank. It is usually closed during regular operation to prevent fuel vapors from escaping into the atmosphere. When the vent control valve fails to respond to prompts from the Powertrain Control Module (PCM) to open and close, the P0446 code is triggered. The only symptom of P0446 in the Toyota Echo is typically the check engine light, although there may be a slight decrease in fuel economy as well.
To fix this issue, it is recommended to test the vent valve circuit from the ECM to the valve to ensure that it is closing and receiving power when the key is on. Checking the resistance on the control circuit against the specifications in the vehicle’s manual is also necessary.
Please note that the information provided is based on the search results and may not cover all possible causes and solutions for the P0446 code on a Toyota Echo. It is always best to consult a professional mechanic or refer to the vehicle’s service manual for accurate diagnosis and repair guidance.
Contents
- What is the EVAP code on a Toyota Echo?
- How do I fix my EVAP problem?
- What is EVAP vent control?
- Where is the EVAP control system located?
- How do I fix code P0446?
- What is the code P0446 on a 2001 Toyota Echo?
- What is the code P0171 on a Toyota Echo?
- Where is the EVAP vent valve located?
- What is code P0440 for Toyota Echo?
- What is the most common cause of the P0446 code?
What is the EVAP code on a Toyota Echo?
The P0441 OBD-II code is relatively rare (at least for Toyotas). It indicates an Evaporative Emission Control System Incorrect Purge Flow. Get your OEM filler caps here.
How do I fix my EVAP problem?
The easiest solution may be to remove and reaffix the gas cap. Once you do, clear the code on the OBD-II diagnostic scanner and drive for a few days. If the code does not return, your gas cap likely was the culprit.
What is EVAP vent control?
The EVAP system is designed to stop fuel system fumes from leaking directly into the atmosphere. Vent lines from the fuel tank pass vapors to the vapor canister, where they are trapped and stored until the engine is started.
Where is the EVAP control system located?
EVAP system components
Inside the tank, there is a float that signals the computer systems and/or fuel gauge as to how much fuel is in the tank. On newer vehicles, the fuel pump, fuel, filter, and fuel pressure regulator may also be housed inside the fuel tank.
How do I fix code P0446?
And check the o-ring. For any tears or cracks. And make sure it locks back on properly. With some kind of a click. Now in my case everything looked fine so what I did was I wiped the filler neck.
What is the code P0446 on a 2001 Toyota Echo?
Specifically, P0446 indicates an Evaporative Emission Control (EVAP) system vent control circuit malfunction. Typically, this indicates a faulty vent valve, a bad control circuit for that valve, or a blockage in the vent valve. In all cases, it clearly shows the mechanic that a check of the EVAP vent valve is in order.
What is the code P0171 on a Toyota Echo?
Oftentimes, a P0171 means that your Toyota is having trouble with a dirty or faulty mass airflow (MAF) sensor, or a vacuum leak downstream of the MAF sensor (perhaps in the PCV line or in the valve itself). Of course, this code can also signify a bad O2 sensor in bank 1.
Where is the EVAP vent valve located?
Here’s your rear driver’s side wheel. And right behind it you’ll find the canister. And attach to the caster. We have this vent control valve.
What is code P0440 for Toyota Echo?
OBD-II code P0440 represents a general fault in the Evaporative Emission Control (EVAP) System. Basically, this code means that something in the EVAP system is broken.
What is the most common cause of the P0446 code?
What Are Some Causes of a P0446 Code? The reason for the display of a P0446 error code may vary from one brand of vehicle to another. However, the most common causes for this error code are a malfunctioning or clogged vent control valve or issues with the control circuit, such as faulty wiring.