The code P0339 on a Dodge Caravan refers to the Crankshaft Position Sensor Circuit Intermittent. The crankshaft position sensor, also known as the crank position sensor, is an electronic device used in an engine to record the rate at which the crankshaft is spinning. It provides important information to the engine control module (ECM) for controlling ignition and fuel injection [[9]].
When the ECM detects an intermittent high signal or an error signal from the crankshaft sensor, it triggers the P0339 code. Some common symptoms of this code include a no-start condition, check engine light illumination, sudden engine stall, and performance issues.
To diagnose the P0339 code, it typically requires 1.0 hour of labor. The specific diagnosis time and labor rates at auto repair shops can vary depending on factors such as the location, make and model of the vehicle, and even the engine type. Most auto repair shops charge between $75 and $150 per hour.
To fix the P0339 code, it is recommended to visually inspect the related wiring harness and connectors, and check for damaged components or broken, bent, pushed out, or corroded connector pins. In some cases, adding a shim to the crankshaft sensor can commonly correct the issue. However, in some cases, the flex plate may require replacement .
Please note that these are general guidelines, and it is always best to consult with a professional mechanic or refer to the specific diagnostic and repair procedures for your Dodge Caravan model.
I hope this information helps! Let me know if you have any other questions.
Contents
- What causes a crankshaft position sensor to go bad?
- Where is the camshaft sensor and the crankshaft sensor located?
- How do you check a crankshaft sensor?
- Can you still drive with a bad crankshaft position sensor?
- Can a crankshaft sensor cause car to shut off while driving?
- What are the symptoms of a bad or failing crankshaft position sensor?
- What does crankshaft position sensor intermittent mean?
- Is it expensive to fix a crankshaft position sensor?
- What is the 7 symptoms of a bad camshaft position sensor?
- Where is the crankshaft sensor on a Dodge Grand Caravan?
What causes a crankshaft position sensor to go bad?
Crank sensor failure can be caused by wiring problems, sensor damage, or issues with the reluctor wheel. Can a crankshaft sensor cause engine failure? A faulty crankshaft sensor can contribute to engine performance problems and stalling, but it’s not the sole cause of engine failure.
Where is the camshaft sensor and the crankshaft sensor located?
The Camshaft Position sensor is typically located in the cylinder head of the engine and has a cylindrical portion that inserts into the head. The Crankshaft Position sensor is normally located in the timing cover or on the side of the block with a cylindrical portion that inserts into the block.
How do you check a crankshaft sensor?
To do this, remove the plug connection and check the internal resistance of the sensor. If the internal resistance value is 200 to 1,000 ohms (depending on the reference value), the sensor is OK. If the value is 0 ohms, there is a short circuit, and in the case of M Ohm there is an interruption.
Can you still drive with a bad crankshaft position sensor?
Some common symptoms of a bad crankshaft position sensor are an illuminated check engine light, hard starting, and misfires. A bad crankshaft position sensor can prevent your vehicle from starting and leave you stranded somewhere, so it’s best not to drive until you fix this part.
Can a crankshaft sensor cause car to shut off while driving?
Sometimes while driving, an engine may stall for various reasons. A common cause is a faulty CKP sensor or wiring. If either component is having issues and is noticed by the system while the vehicle is in motion, it is likely the cut off of signal will cause the engine to stall and stop running.
What are the symptoms of a bad or failing crankshaft position sensor?
Symptoms of a Bad Crankshaft Sensor
- Check Engine Light.
- Engine Refuses to Start.
- Engine Stalling.
- Rough-Running Engine.
- Reduced Fuel Economy.
What does crankshaft position sensor intermittent mean?
Good to hear that,The code P0339 is a generic code that means “Crankshaft Position Sensor – Intermittent”. It can be caused by a number of things, including a bad crankshaft sensor, a bad wiring harness, or a loose connection.In your case, it sounds like the dead battery may have been the culprit.
Is it expensive to fix a crankshaft position sensor?
The average cost for a Crankshaft Position Sensor Replacement is between $178 and $238. Labor costs are estimated between $96 and $121 while parts are priced between $82 and $117. This range does not include taxes and fees, and does not factor in your unique location.
What is the 7 symptoms of a bad camshaft position sensor?
Performance. And if it’s not functioning optimally. It could impact your car’s power and acceleration. Another symptom to be mindful of is a surge in fuel. Consumption.
Where is the crankshaft sensor on a Dodge Grand Caravan?
So that doesn’t help. There we go try and reach in here.
