What is the code P0339 on a 2011 Dodge Caravan?

Code P0339 on a 2011 Dodge Caravan
The code P0339 on a 2011 Dodge Caravan refers to a problem with the crankshaft position sensor. The crankshaft position sensor, also known as the crank position sensor, is an electronic device used in an engine to record the rate at which the crankshaft is rotating.
When the engine control module (ECM) receives an intermittent high signal or an error signal from the crankshaft position sensor, it stores the P0339 code in its memory. This code indicates that there is an issue with the circuit to the crankshaft position sensor A.
Symptoms and Possible Causes
The most common symptoms of the P0339 code include:
1. No start condition
2. Check engine light illumination
3. Sudden engine stall
4. Performance issues
The possible causes of the P0339 code can vary, but they may include:
1. Faulty crankshaft position sensor
2. Damaged or corroded wiring harness and connectors related to the sensor
3. Broken, bent, pushed out, or corroded connector pins
Diagnosis and Repair
To diagnose the P0339 code, it typically requires 1.0 hour of labor. The specific diagnosis time and labor rates at auto repair shops can differ based on factors such as the location, make and model of the vehicle, and even the engine type. It is common for most auto repair shops to charge between $75 and $150 per hour.
To fix the P0339 code, the following steps are recommended:
1. Visually inspect the related wiring harness and connectors for any damage or corrosion.
2. Check for damaged components and look for broken, bent, pushed out, or corroded connector pins.
3. If any issues are found during the inspection, repair or replace the affected components as necessary.
It’s important to note that these steps are general recommendations, and it’s always best to consult with a qualified mechanic or refer to the vehicle’s service manual for specific instructions related to your 2011 Dodge Caravan.
I hope this information helps! Let me know if you have any other questions.

What happens when camshaft position sensor goes bad?

A failing camshaft position sensor begins losing its ability to quickly transfer data. Mismatched fuel delivery and ignition timing, even if off by a few milliseconds, will cause your vehicle to sputter, accelerate poorly, lack power, stall or even shut off.

What does crankshaft position sensor intermittent mean?

Good to hear that,The code P0339 is a generic code that means “Crankshaft Position Sensor – Intermittent”. It can be caused by a number of things, including a bad crankshaft sensor, a bad wiring harness, or a loose connection.In your case, it sounds like the dead battery may have been the culprit.

How do you start a car with a bad crankshaft sensor?

Starting a vehicle with a bad crankshaft sensor can be risky and it’s unlikely to work. Disconnect the damaged sensor and try spraying a little starter fluid in the throttle body on your engine. Then, try cranking the engine to start the vehicle.

What are the symptoms of a bad or failing crankshaft position sensor?

Symptoms of a Bad Crankshaft Sensor

• Check Engine Light.
• Engine Refuses to Start.
• Engine Stalling.
• Rough-Running Engine.
• Reduced Fuel Economy.

Can you still drive with a bad crankshaft position sensor?

Some common symptoms of a bad crankshaft position sensor are an illuminated check engine light, hard starting, and misfires. A bad crankshaft position sensor can prevent your vehicle from starting and leave you stranded somewhere, so it’s best not to drive until you fix this part.

What causes a crankshaft position sensor to go bad?

Crank sensor failure can be caused by wiring problems, sensor damage, or issues with the reluctor wheel. Can a crankshaft sensor cause engine failure? A faulty crankshaft sensor can contribute to engine performance problems and stalling, but it’s not the sole cause of engine failure.

Will disconnecting battery reset crankshaft sensor?

Disconnecting the battery will not reset the crankshaft position sensor. The crankshaft position sensor does not contain any internal memory, so resetting it requires either replacing the sensor or recalibrating it through a diagnostic procedure.

Does a bad crankshaft position sensor always throw a code?

Cam and crank position sensors will throw a code. There are a lot of things that can cause it run poorly without throwing a code. Too many to mention, really. You can probably rule out bad sensors if the CEL isn’t on.

How much does it cost to fix a crankshaft position sensor?

The average cost for a Crankshaft Position Sensor Replacement is between $178 and $238. Labor costs are estimated between $96 and $121 while parts are priced between $82 and $117. This range does not include taxes and fees, and does not factor in your unique location.

What causes the code P0339?

Common causes of the P0339 code include a defective crankshaft position sensor or reluctor wheel, damaged wiring, poor connections, faulty PCM, or timing belt issues.