What is the code C1223 on a Toyota FJ Cruiser?

Understanding the Code C1223 on a Toyota FJ Cruiser
The code C1223 on a Toyota FJ Cruiser indicates an issue with the Anti-Lock Brake System (ABS) Control System. Specifically, it points to a malfunction in the left rear wheel speed sensor, often resulting in a zero input signal. This trouble code is typically accompanied by the illumination of the check engine light and/or the anti-lock brake system light in the instrument cluster.
Symptoms and Diagnosis
When the ABS control system is not set to factory specifications, the C1223 code is triggered. The diagnosis of this code typically requires 1.0 hour of labor, and the specific diagnosis time and labor rates at auto repair shops can vary based on factors such as the location, make and model of the vehicle, and even the engine type. It is common for most auto repair shops to charge between $75 and $150 per hour for this diagnosis .
Conclusion
In summary, the C1223 code on a Toyota FJ Cruiser points to a malfunction in the left rear wheel speed sensor and indicates an issue with the ABS Control System. If you encounter this code, it is advisable to have the ABS system inspected and repaired by a qualified technician to ensure the safety and proper functioning of the vehicle.

What is the code C1226?

Wheel Speed Sensors: DTC C1226 RF Excessive Wheel Speed Variation indicates R F (not LF) wheel speed sensor is either sending a bad signal or no signal. Start by checking the connections. The wheel speed sensors are integrated into the wheel bearing/hub assembly.

What is the C1225 of excessive wheel speed variation?

C1225 is usually caused by a faulty wheel speed sensor, the wheel speed sensor can only be replaced by replacing the entire hub and bearing assembly, you would want to make sure it is the sensor cuasing the problem through electrical testing and visual inspections, any play in the wheel bearing will cause erratic …

What does C1225 mean?

C1225: Wheel Speed Sensor Malfunction (Abnormality in tyre size) caution. If there is any problem in the CAN bus lines, an incorrect diagnosis code may be set. Prior to this diagnosis, diagnose the CAN bus lines (Refer to GROUP 54C – CAN Bus Diagnostics Table .).

What is trouble code C1233?

Cause. Connected a scan tool and found code C1233 – Right Front Wheel Speed Circuit Open Or Shorted. Performed a road test, used the scan tool to monitor live data and found the right front ABS wheel speed sensor signal parameter was not present.

What is the code C1223 on gx470?

C1241 is low voltage warning and C1223 is an ABS control system malfunction.

What is the error code for transmission speed sensor?

A P0500 code is a diagnostic trouble code (DTC) titled “Vehicle Speed Sensor (VSS) Malfunction.” This code is triggered when the vehicle’s Powertrain Control Module (PCM) or Engine Control Module (ECM) detects inaccurate speed readings or lack of a signal from the Vehicle Speed Sensor (VSS).

What is C1234 code?

Fault code C1234 is often caused by a faulty ABS sensor. In most cases, this sensor can be found on the wheel hub or on the axle of your car. Diagnosing and replacing a faulty ABS sensor is relatively easy and can usually be done without the need for any specialist tools.

What is trouble code P215A?

DTC P215A will set if there is a di erence between vehicle speed and Anti- lock Braking System ( ABS ) wheel speed greater than 7.5mph (12km/h) in an I-Shift / mDRIVE equipped vehicle. Using Tech Tool verify the vehicle speed factor is set to the correct value.

How do I fix my C1223 code?

Repairs can be relatively straightforward if the cause of the C1223 issue is a defective brake warning light. This can be the case with the remaining C1224-C1226 codes as this is the first component that should be inspected. All that is needed in this instance is that the faulty brake light is replaced with a new one.

What does C1233 code mean?

The C1233 is a fairly straight forward code pointing to a problem with the driver’s side front Wheel Speed Sensor (aka “ABS Sensor”). The sensor is mounted to the rear of the front wheel assembly, behind the brake system. Inspect the electrical connector and wire harness for any loose, broken or damaged wires.