What filter do I need to change oil in Honda Insight 2010?

To change the oil in a Honda Insight 2010, you will need the following:
– Engine oil: The 2010 Honda Insight has an engine oil capacity of 3.2 quarts.
– Oil filter: You will need a new oil filter.
Here are the steps to change the oil in a Honda Insight 2010:
1. Gather the necessary tools and materials, including a wrench, a drain pan, a new oil filter, and the appropriate amount of engine oil.
2. Locate the oil drain plug, oil filter, oil fill cap, and dipstick. The oil drain plug is on the aft side of the engine. The oil filter is typically located near the bottom of the engine.
3. Place the drain pan underneath the oil drain plug.
4. Use the wrench to loosen and remove the oil drain plug, allowing the old oil to drain into the pan.
5. Once the oil has completely drained, replace the oil drain plug and tighten it securely.
6. Locate the oil filter and use an oil filter wrench, if necessary, to remove the old oil filter.
7. Apply a thin layer of oil to the rubber gasket of the new oil filter.
8. Install the new oil filter by hand, making sure it is tightened securely.
9. Remove the oil fill cap and pour the appropriate amount of engine oil into the engine. The 2010 Honda Insight requires 3.2 quarts of engine oil.
10. Replace the oil fill cap.
11. Start the engine and let it run for a few minutes to circulate the new oil.
12. Turn off the engine and check the oil level using the dipstick. Add more oil if necessary.
13. Dispose of the old oil and filter properly.
Please note that these instructions are a general guide and it’s always recommended to consult the owner’s manual for your specific vehicle model for detailed instructions and specifications.

What is the best engine oil for Honda Insight?

• Mobil 1 Full Synthetic Engine Oil 5W-20 5 Quart.
• Pennzoil Pennzoil Full Synthetic Motor Oil SAE 0W-20 5 Quart.
• Valvoline Restore & Protect Full Synthetic Engine Oil 5W-30 5 Quart.
• STP High Mileage Full Synthetic Engine Oil 0W-20 1 Quart.
• STP Standard Full Synthetic Engine Oil 0W-20 5 Quart.

Do I need a filter with every oil change?

Many manufacturers recommend that the oil filter be replaced every second time you get your oil changed. So, if you’re on a 3,000-mile cycle you’d change your filter every 6,000; if you’re on a 6,000-mile cycle (as with most modern vehicles) you’d change out every 12,000.

How much oil does a 2010 Honda Insight take?

It’s in your manual – about 3.4 quarts. I’m sure there are some that will say 0W-20 of one brand or another will get you better mileage, but it’s unlikely to ever be noticeable.

Do you need a special oil filter for synthetic oil?

If you are using synthetic oil, do you need a synthetic oil filter? No. The use of the word “synthetic” in the case of synthetic oil filters refers to the material it’s made from. Synthetic media is used in the manufacturing process, rather than traditional pleated paper.

Is it OK to change oil but not filter?

A common confusion regarding car oil is whether you can change the oil without changing the filter. A simple answer is, ‘Yes, you don’t always have to change the filter‘. For optimal performance, however, it’s imperative to know what an oil filter actually does and when exactly you need to change it.

Does it matter which oil filter I buy?

Oil filter quality does make a difference. Friction, heat, and particles are your engine’s enemy. Only an OEM filter is designed to lubricate according to your engine specifications.

How do I know what type of oil filter I need?

The variations in oil filter design, including spin-on, cartridge, magnetic, and high-efficiency filters, cater to different engine requirements. Car-specific filters may differ in size, thread pitch, and design, emphasizing the importance of consulting your vehicle’s manual.

What happens if you change the oil but not the filter?

Without a clean and effective oil filter, the engine oil can become contaminated with particles such as dirt, metal shavings, and sludge. These contaminants can compromise the oil’s ability to lubricate engine components properly.

What filter do you change with oil change?

The oil filter is also changed during an oil change and that is because the oil filter is the tool for cleaning the motor oil as it runs through the engine. The reason it has to be changed is that it also looses its effectiveness, and then cannot clean the motor oil.

What kind of oil does 2010 Honda Insight take?

Oil Grade: API*

Viscosity:	0W-20 (All TEMPS)
Capacity:	3.2 quarts. w/of. After refill check oil level.
Capacity:	3.4 quarts (with filter). After refill check oil level.
Torque:	29 ft/lbs (Oil Drain Plug) Install a new washer on the drain bolt. Only use an OE drain plug.