What does it mean when my Dodge Ram says perform service?

When your Dodge Ram displays a “Perform Service” message, it typically indicates that a specific maintenance task needs to be performed. The exact meaning of the message can vary depending on the model year and engine type of your Ram. Here are some common reasons for the “Perform Service” message:
1. CCV Filter Replacement: On some Ram models, the “Perform Service” message is a reminder to replace the CCV (Crankcase Ventilation) filter. This service is typically recommended every 67,500 miles.
2. EGR Valve and Cooler Cleaning: For certain Ram 2500 models from 2007 to 2012, the “Perform Service” message may indicate the need to clean the EGR (Exhaust Gas Recirculation) valve and cooler.
3. Oil Change: In some cases, the “Perform Service” message may simply be a reminder that an oil change is due. The recommended oil change interval for Ram 2500 models is typically between 7,500 and 10,000 miles, depending on the model year.
To reset the “Perform Service” message, you may need to follow specific procedures depending on your Ram model. For example, on some models, you can turn the key to the accessory position, press the brake pedal twice, and then press the accelerator pedal twice slowly within 10 seconds. It’s always a good idea to consult your vehicle’s manual or reach out to a certified Dodge dealer for the correct reset procedure.
Remember to perform the necessary maintenance tasks indicated by the “Perform Service” message to ensure the proper functioning and longevity of your Dodge Ram.
I hope this helps! Let me know if you have any other questions.

Why does it say service on my dashboard?

The “Check Engine” or “Service Engine Soon” light indicates there may be a repair or replacement of your engine or transmission. It means there is more than a routine repair or service requirement, and instead, a system failure to the fuel, transmission, ignition, or emissions.

How do you reset service indicator?

Quick and Easy Steps to Reset the Maintenance Required Light

1. 1 Turn your car on, but do not start the engine.
2. 2 Change the dashboard display to “TRIP A.”
3. 3 Switch your car off and hold the “ODO/TRIP” button down.
4. 4 Start your car, but don’t turn on the engine.
5. 5 Hold the “ODO/TRIP” button down for 10 seconds.

How do I reset my Dodge Ram computer?

To reset the computer in your RAM 1500, take the following steps:

1. Identify your battery’s negative cable.
2. Disconnect the negative cable from the battery.
3. Wait 20 minutes so that all systems have shut down.
4. Reconnect the negative cable.

How do you reset a service engine?

The procedure is that simple locate the battery. And identify its terminal terminals. Then take a suitable socket or wrench loosen. Up the negative cable. And remove it from the battery’s post.

What does the perform service light mean?

Most of the time, a “Perform Service” light means it’s time to change your oil. Other car manufacturers have similar indicators that mean the same or similar things, and specific Jeep models of certain model years might differ slightly as to what this light means.

How do you reset the perform service on a 2011 Ram 2500?

You have to put up with my big old French bread feet for a second here. But anyway one two one two three okay turn the ignition.

How do you clear the code on a Dodge Cummins?

Using a code reader tool, connect to the ECM and find the “fault codes” tab. The displayed codes can generally be clicked on one by one. Another option is to select “erase all faults” and then follow the onscreen instructions. At the end of the procedure, the ignition key should be turned off.

Is it OK to drive with service light on?

The general rule-of-thumb is anything in RED (such as brakes, low oil pressure, etc.) is critical and could cost you your engine or your life. If one of these lights comes on, pull off the road, stop, and shut the engine off as quickly as you can safely.

How do I reset my service maintenance?

Quick and Easy Steps to Reset the Maintenance Required Light

1. 1 Turn your car on, but do not start the engine.
2. 2 Change the dashboard display to “TRIP A.”
3. 3 Switch your car off and hold the “ODO/TRIP” button down.
4. 4 Start your car, but don’t turn on the engine.
5. 5 Hold the “ODO/TRIP” button down for 10 seconds.

How do I reset the perform service message?

And then turn the ignition off. And once you do that go ahead and start the engine. Be sure that the message has been reset Tony message that I should be showing is for my TPMS.