Based on the search results, I couldn’t find a specific measurement for the width of a 1957 Chevy rear end. However, I found some information that might be helpful.
According to a forum post on the Chevy Tri Five Forum, the rear end width of a 1957 Chevy can vary depending on the specific model and configuration. The forum member mentioned that the rear end width on their 1957 Chevy was about 60 inches from flange to flange. Another forum post on the same forum mentioned that the rear end width of a 1955-1957 Chevy can be measured from drum to drum at the wheel mounting surface.
It’s important to note that these measurements are based on forum discussions and may not be universally applicable to all 1957 Chevy models. To get the most accurate measurement for a specific 1957 Chevy rear end, it would be best to consult a reliable source or reach out to a knowledgeable mechanic or specialist.
I hope this information helps! Let me know if there’s anything else I can assist you with.
Contents
- Are 55 and 57 Chevy frames the same?
- What is the width of a 57 Chevy rear end?
- How wide is a 67 Nova rear end?
- How wide is a 1953 belair rear end?
- How wide is the rear end of a 55 Chevy truck?
- What is the width of a 53 Chevy rear end?
- How wide is the rear axle on a 1954 Chevy truck?
- How wide is a 56 Chevy truck rear end?
- How wide is a 1957 Chevy?
- What were the specs of the 57 Chevy?
Are 55 and 57 Chevy frames the same?
The 55/56 frame utilizes an open C-channel front horn. The 57 employs a box type front horn. Rear frame horn construction is identical except the 57 rear bumper bracket bolt hole spacing is not quite the same as the 55/56. Other than these differences the frame is basically the same.”
What is the width of a 57 Chevy rear end?
A stock 57 rear end is 60″ mounting surface to mounting surface.
How wide is a 67 Nova rear end?
Products specifications
| Vehicle Fitment | 62-72 GM X-body vehicles (Nova, Chevy II, Super Sport, Apollo, Omega, Ventura) with single or multi-leaf rear springs |
|---|---|
| Brake Space | 2.5 inch axle standoff |
| Width | 62-67 = 57.875 inches / 68-72 = 60.250 inches (between wheel mounting surfaces) |
How wide is a 1953 belair rear end?
Rear end width is 60″, not counting fractions of an inch, if any. Measurement is drum to drum, where wheel mounts to drum surface.
How wide is the rear end of a 55 Chevy truck?
The standard width is 60″ Axle Flange to Axle Flange but custom widths are available.
What is the width of a 53 Chevy rear end?
Rear end width is 60″, not counting fractions of an inch, if any. Measurement is drum to drum, where wheel mounts to drum surface.
How wide is the rear axle on a 1954 Chevy truck?
The rear axle width is 62-3/8″ from wheel mount to wheel mount.
How wide is a 56 Chevy truck rear end?
55-57 Chevy is 60-1/4″.
How wide is a 1957 Chevy?
Technical specs | Chevrolet Bel Air 2-door Coupé 1957 is 1.877 m wide and 1.521 m high.
What were the specs of the 57 Chevy?
For 1957 there were four standard engine options, a 235.5 cu in (3,859 cc) inline 6-cylinder producing 140 hp (104 kW), a 265 cu in (4,340 cc) V8 “Turbo-Fire” producing 162 hp (121 kW), and two 283 cu in (4,640 cc) V8s: a “Turbo-Fire” twin-barrel carburetor producing 185 hp (138 kW) and a “Super “Turbo-Fire” four- …
