How to use Subaru Outback headlights?

How to Use Subaru Outback Headlights
Using the headlights on your Subaru Outback is a straightforward process. Here are the steps to follow:
1. Turn on the headlights: Locate the headlight switch, which is typically located on the left side of the steering wheel. Turn the switch to the “On” position to activate the headlights. The headlights will illuminate the road ahead and improve visibility.
2. Switch between high beam and low beam: The Subaru Outback is equipped with both high beam and low beam headlights. The high beam headlights provide maximum illumination and are used when driving on dark, unlit roads with no oncoming traffic. The low beam headlights provide a lower, more focused beam of light and are used in normal driving conditions or when there is oncoming traffic.
– To switch to high beam headlights, push the headlight switch forward or pull it towards you, depending on the model.
– To switch back to low beam headlights, push the headlight switch back or push it away from you.
3. Adjust the headlight aim: Properly aimed headlights are essential for optimal visibility and safety. If you feel that the trajectory path of your headlights is not aligned correctly, you can adjust the aim. Here’s how:
– Park your Subaru Outback on a level surface facing a wall or garage door.
– Measure the distance from the center of each headlight to the ground and transfer the measurements to the wall using bright-colored masking tape for better visibility.
– Locate the adjustment screws on the headlight assembly. These screws control the headlight angle regardless of the beam setting.
– Test the aim of your low beam headlights against the marks on the wall. Adjust the screws as needed to align the trajectory path.
– Repeat the process for the high beam headlights.
It’s important to note that if you are unsure about adjusting the headlight aim yourself, it is recommended to consult the owner’s manual or seek assistance from a professional technician.
Remember, maintaining properly functioning headlights is crucial for your safety on the road. If you notice reduced nighttime visibility or the need for a headlight bulb replacement, it is recommended to replace the bulbs promptly to ensure optimal performance and safety [[10]].

How do you set your headlights to auto?

Put the vehicle in park turn the power mode to on. And put the light switch lever in the auto. Position. Then pull the light switch lever toward you and hold it for at least 40 seconds.

How do I turn my headlights on auto?

Position when you do this the auto on off feature is also turned. Off. Then you can engage high beams as needed by pushing the control stock forward and return to low beams by pulling. It back.

How do you turn on automatic headlights on a Subaru?

And then push your stick. Forward for high beams. Simply turn the strip to auto. And push it forward for high beams. That’s all you need to do.

How do Subaru headlights work?

Which can help you see better around corners by aiming your headlights toward the direction you’re turning. Rather than simply pointing straight ahead. That way you can see farther around the corner.

How should I set my headlights?

Find the adjusting screw and turn the screws slowly clockwise to raise the height of the lights or counterclockwise to lower them. As you make your adjustment, make sure the most intense part of the headlight beam hits at or just below the vertical centerline you taped on the wall.

Does Subaru Outback have automatic headlights?

And then you tap this forward. Your high beams will be turned on you’ll see the blue light there. And if you ever want to turn those off you just tap it again and it turns it off.

Does Subaru have automatic high beams?

Your hands stay on the steering wheel while using High Beam Assist. You’ll see better, and drive more safely without having to constantly adjust your lights. Better yet – you won’t forget to adjust your lights – which means a better drive for you AND for the other drivers on the road.

How do I use my headlights?

Position to flash the high beams pull the lever back and then release. It you can manually turn the exterior lights off when the power is on and the vehicle is in park.

How do you turn on the brights in a Subaru Outback?

Here. So you’re going to turn it to auto. And then you’re going to push it. Forward. So what that’s going to do is it’s not going to turn your high beams. On if it’s during the daytime.

What is the symbol for automatic headlights?

If the car has automatic headlights, the setting is often indicated by the word “auto” or just the letter A. Bright lights are usually engaged by moving the stalk forward. This will also illuminate a blue dashboard light with the headlight symbol. Moving the stalk forward again turns the brights off.