How to change a tail light on a Chevy HHR?

Changing the Tail Light on a Chevy HHR
To change the tail light on a Chevy HHR, you can follow these steps:
1. Identify the Problem: An easy indication of a brake light out is the turn signal blinking at a much faster rate than normal on the side that the bulb is burnt out.
2. Access the Bulb Sockets: Lift the tailgate and locate the access panels on either side of the cargo area to access the bulb sockets. Use a flathead screwdriver to apply pressure to the panel to release and remove it.
3. Remove the Bulb: With the panel removed, you will have easy access to the bulb sockets for both the brake and reverse lights. Remove the old bulb and replace it with a new one.
4. Consider Replacement: If your tail light assembly needs to be replaced, you can consider getting a tail light assembly replacement for Chevy HHR from a trusted source like AutoZone or Amazon.
5. Additional Resources: You can also refer to videos and guides available online for visual assistance in changing the tail light on your Chevy HHR .
6. Consider LED Bulbs: If you are considering installing LED tail light bulbs, it’s important to note that a load resistor must be used for each LED turn signal bulb used, and it should be mounted to an area that won’t melt.
By following these steps, you should be able to change the tail light on your Chevy HHR.

Will AutoZone change my tail light for me?

While AutoZone doesn’t offer actual brake light replacement services, our team can assist you with any questions about the process, help you find the right products to get started, and maybe even give you a hand. How do you remove a brake light to replace it?

Are the brake light and tail light the same bulb?

Are My Tail Lights and Brake Lights Using the Same Bulb? On many vehicles, the tail lights and brake lights share the same bulb. One filament inside the bulb is for the tail light and the other filament is for the brake light. There are also some vehicles that have a separate bulb for each circuit.

How do you replace a whole tail light assembly?

Some Wing nuts. And just grab the tail light assembly. And it slides right out from here you can replace the bulbs. Nice and easy comes right out or if you want to replace the whole assembly.

Can you replace a tail light by yourself?

Replacing your car’s tail light bulbs is a simple and straightforward procedure. The rear light bulbs are usually housed in a single unit that’s easy to access from inside the boot. Haynes has full step-by-step information on how to do this. Most tail light bulbs are filled with halogen gas, and are readily available.

What do I do if my tail light cover is broken?

You probably don’t need to have the light fixture repaired immediately, but you will want do a temporary fix at home. If you simply have a crack in your tail light cover, some craft glue may do the trick. But, if the damage is more severe, you’ll want to cover the exposed area with some lens repair tape.

How much does it cost to replace one tail light?

TAIL LIGHT BULB REPLACEMENT PRICING
The average cost to replace your tail light bulb is $20 – $100. Pricing may vary based on the type of car you have, as well as the type of (and quality) auto shop that you go to.

How do you remove and replace a tail light bulb?

Turn this bulb socket to the left to release it from the assembly. In most cases your old bulb will slip straight out of the socket.

How do you replace a rear tail light assembly?

How To Replace a Tail Light

1. Step 1: Open trunk or tailgate.
2. Step 2: Pull tail lamp assembly out (if needed)
3. Step 3: Pull bulb out.
4. Step 4: Add bulb grease, put new bulb in.
5. Step 5: Reattach assembly (if needed)
6. Step 6: Repeat on other side.

Does O Reilly change tail light bulbs?

Our parts professionals will even install headlights and tail lights for free on most vehicles when you purchase them in-store. Ask about our free bulb installation service at your local O’Reilly Auto Parts.

How do you remove a tail light bulb from a Chevy?

On the backside of the tail light assembly you’ll see the back of the light socket with wires connected to it. Locate the socket holding the burned-out bulb and grip the rear of it. Rotate the socket to the left and pull it out of the backside of the light.