How much torque does a Ford Bronco axle nut have?

Torque Specifications for Ford Bronco Axle Nut
The torque specifications for the axle nut on a Ford Bronco can vary depending on the specific model and year. Here are the torque specifications based on the search results:
– Source 1 mentions that the outer nut should be torqued to 150 ft lbs.
– Source 2 also indicates that the axle nut torque is 221 lb.ft.
– Source 3 provides information about the lug nut torque, which is 100 ft-lbs for a 2022 Ford Bronco.
– Source 7 mentions that the factory manual calls for 50 ft lbs for the spindle nut and then back off 1/4 turn.
Based on the information from the search results, the torque specifications for the Ford Bronco axle nut can range from 50 ft lbs to 221 lb.ft. It’s important to refer to the specific model and year of the Ford Bronco to determine the exact torque specification for the axle nut.
If you have a specific model and year of the Ford Bronco in mind, it’s recommended to consult the vehicle’s manual or reach out to a certified Ford dealership for the most accurate and up-to-date information on the axle nut torque specification.

How many foot pounds of torque do I need for wheel nuts?

80 to 90 ft-lbs
And when you look at that, and realize that the average torque required on a lug nut, to hold the wheel on, is 80 to 90 ft-lbs, well you can imagine how over-tightened some of these lug nuts are. Now that’s a problem because it almost guarantees warped brake rotors.

What is the torque on the axle nut on a Ford f150?

258 lb. ft would be a normal and expected torque spec for an axle nut of this size, I often see axle nuts and bolts that require 250-350 lb.

What is the torque on the axle nut on a 2017 Ford f150?

Notes: Axle nut torque: 30 lb-ft / 40 Nm.

What is the torque spec for axle nut?

On some wheel bearings sets and hub units, the axle nut secures the outer flange to a CV joint or stub axle. As the nut is tightened, it pulls the flange and axle together to set the preload of bearings. These axle nuts will have specifications as low as 130-foot pounds and as high as 300-foot pounds.

How tight should axle nut be?

I’m going to go ahead and look for my hole. Right here which is where my cotter pin is going to go. So if I tighten this down my fingers. I can go about that tight okay.

What are the torque specs on a Ford?

Ford Engine Bolt Torque Chart

Fastener Type	Torque Spec
Connecting rod bolts	40-45 ft-lbs.
Cylinder head bolts	90-100 ft-lbs.
Rocker arms	17-23 ft-lbs.
Intake manifold bolts	23-25 ft-lbs.

What is the torque on the axle nut on a 2013 Ford Flex?

Notes: Axle nut torque: 250-ft / 358 Nm.

What is the torque on the axle nut on a 2012 Ford Flex?

Axle nut torque specifications: tighten old wheel hub to 258 ft-lb/350 Nm to seat the half shaft. Remove and discard old nut. With vehicle raised, apply the brake so the half shaft will not rotate. Install new nut and tighten to 258ft-lb/350 Nm.

What is the torque spec for spindle nut?

4) For one-piece spindle nut systems, torque the nut to a minimum of 300 ft- lbs. Do not back off the spindle nut. Engage any locking device that is part of the spindle nut system. If the locking device cannot be engaged when the nut is at 300 ft-lbs, advance the nut until engagement takes place and the nut is locked.

Can you over tighten an axle nut?

Extreme overtightening of the axle nut may cause undue wear on the stubaxle threads and/or crushing of the inner spacer between the bearings – but I doubt that you’ve overdone it based upon your description – I wouldn’t lose any sleep over it.