How much does it cost to replace a CV joint on a Honda?

Cost to Replace a CV Joint on a Honda
The cost to replace a CV joint on a Honda can vary based on several factors, including the specific model of the Honda and whether you are replacing one or both components. Here’s a breakdown of the potential costs involved:
1. Parts and Labor:
– The cost of replacing a CV joint on a Honda can range from $150 to $750, depending on whether you are replacing one or both components. The price of a new axle shaft for a Honda can be between $86 to $200, and when combined with parts and labor, the total cost can fall within the mentioned range.
2. Average Cost:
– On average, it costs about $350 to replace a CV axle on most vehicles, including Hondas. This cost typically does not include a wheel alignment, which may or may not be necessary depending on the specific work done.
3. Factors Affecting Cost:
– The cost of replacing a CV joint can be influenced by factors such as the type of car, the specific model of the Honda, and the brand of the CV joint. Additionally, labor rates can vary from shop to shop, and the total labor cost will depend on how many axles are being replaced.
In summary, the cost to replace a CV joint on a Honda can range from $150 to $750, with an average cost of about $350. It’s important to note that these costs are estimates and can vary based on various factors, including the specific model of the Honda and the labor rates of the repair shop.

Is a CV joint easy to replace?

Replacing a CV joint yourself will save you a fair bit of money, but will require a decent amount of mechanical expertise and time. If you think the job is too complicated, it’s recommended that you leave the task to a qualified technician. This can also help protect you from voiding any motor plan or warranty.

Is a CV joint expensive to fix?

The average cost for a CV Joint Replacement is between $1,111 and $1,159 but can vary from car to car.

What causes CV joints to go bad?

Bad or damaged engine mounts will cause the cv axle to keep breaking, overloading vehicles beyond its capacity and stress the axles with large bumps and potholes also will damage the cv joint too. Another way drivers can put their CV parts at greater risk is by adding lift kits to their vehicle.

How long does it take to fix a CV joint?

between 1.5-3 hours
CV Axle Replacement Expenses
Replacement axle shafts can be bought for between $60-150.00 each, and labor is generally between 1.5-3 hours to replace, bringing labor to around $150-350.00.

Is replacing CV joints a big job?

Most outer boots can be replaced without removing the complete CV axle. While it’s still a lot of work to get to the outer boot ( removing the brake caliper, bracket, and separating a ball joint), sometimes pulling the complete CV axle out can be the most challenging of all.

How long will a bad CV joint last?

But the average lifespan of a bad CV axle is around five to six months. Knowing this does not merely mean to stretch the deadline a little bit. You might be thinking that you can save more money by postponing the checkup for your ATV/UTV. But I’d suggest you take your vehicle to the service center as soon as possible.

How many miles do CV joints last?

100,000 miles
To keep that all-important grease contained where it should be, each joint is enshrouded by a protective rubber boot, or “CV boot.” As long as that boot remains intact, it is not uncommon for CV joints to last well over 100,000 miles or more.

Can you drive with a bad CV joint?

The Constant Velocity is sealed by a boot. This boot may get damaged, and when this happens, the joint will wear out and eventually fail. If you drive a car with a damaged CV, the joint will disintegrate further, making driving impossible. You’ll not be able to control the vehicle and may get involved in an accident.

What are the symptoms of a bad CV joint?

The third symptom is the leaking CV axle boot you’ll usually find grease build on the inner portion of the tires. Suspension parts and on the ground when this happens dirt moisture.

How to tell the difference between bad wheel bearing bad CV joint?

To tell the difference between a bad wheel bearing and a bad CV joint, listen to the noise. If you hear a grinding, growling, or rumbling noise coming from the affected wheel, it’s a bad wheel bearing. If you hear a clicking noise coming from the affected wheel when turning, it’s a bad CV joint.