Rear End Length of a 1955 Chevy
The rear end length of a 1955 Chevy varies depending on the specific model and configuration. However, based on the information available, the rear axle length of a 1955 Chevrolet Bel Air Hardtop Sport Coupe RWD is a little over 60 inches. Additionally, Currie 9-inch rear ends for 1955 through 1957 GM B-body vehicles are built to match the vehicle’s original equipment axle width, pinion location, suspension mounting points, and wheel bolt pattern, providing a direct bolt-in solution for those looking to upgrade the rear end of their classic “Tri-5” Chevy build.
It’s important to note that the specific rear end length may vary based on the model and any modifications that have been made to the vehicle. If you have a specific model or configuration in mind, it’s recommended to consult with a professional or refer to the vehicle’s specifications for precise measurements.
Contents
- How much did a 55 Chevy cost?
- How wide is the axle on a 55 Chevy?
- How wide is the rear end of a 55 Chevy truck?
- What is the rear end ratio of a 55 Chevy?
- How long is a 55 Chevy drive shaft?
- What is the nickname for the 55 Chevy?
- How long is a 55 Chevy?
- How wide is a 1957 Chevy rear end?
- How wide is a 57 Chevy Rearend?
- How wide is a 56 Chevy truck rear end?
How much did a 55 Chevy cost?
The Bel Air two-door Nomad station wagon was added to the line in February 1955, and the 210 sport coupe was added to the line in June 1955. When it came to pricing, the 1955 Chevrolet Bel Air Beauville four-door wagon came in at $2,361, and the popular Bel Air sport coupe cost $2,166.
How wide is the axle on a 55 Chevy?
The standard width is 60″ Axle Flange to Axle Flange but custom widths are available.
How wide is the rear end of a 55 Chevy truck?
It’s about 61″ wide (mounting surface to mounting surface), slightly wider than the oem axle at 60 1/4″.
What is the rear end ratio of a 55 Chevy?
FROM THE FACTORY IN 1955 there were ONLY 3 gear ratios: 3.55 (Powerglide tranny), 3.70 (3sp), 4.11 (3spOD). Now, here is a test for those who think they know their 55-56 rear gear ratios.
How long is a 55 Chevy drive shaft?
The full length of the drive shaft is 54 inches from U-joint center to center.
What is the nickname for the 55 Chevy?
The 1955, 1956 and 1957 Chevrolets are sought after by collectors, enthusiasts and hot rodders, and the three model years are often referred to by the given nickname of the “tri-fives.” Collectors will pay a premium for two-door models, and even more for the Bel Air version, especially the two-door hardtop (two-door, …
How long is a 55 Chevy?
Handling. The 1955 Chevrolet Bel Air measures 73.00 inches in width, The 1955 Chevrolet Bel Air measures 195.60 inches in length, and has a wheelbase of 115.00 inches.
How wide is a 1957 Chevy rear end?
60 inches
Products specifications
| Vehicle Fitment | 55-57 Chevy Tri-5 (120, 210, Bel Air and Delray ) Call for Station Wagons, Nomad and Sedan Delivery |
|---|---|
| Brake Space | 2.5 inches (axle standoff) |
| Width | 60 inches (between wheel mounting surfaces) |
| Oil Capacity | 3 quarts of 85w-140, non-synthetic (API GL-6 rated only) |
How wide is a 57 Chevy Rearend?
A stock 57 rear end is 60″ mounting surface to mounting surface.
How wide is a 56 Chevy truck rear end?
55-57 Chevy is 60-1/4″.
