The length of Ford Explorer axles can vary depending on the specific model and configuration. However, it is worth noting that the Ford Explorer 8.8 rear axle has a longer driver’s side axle tube compared to the passenger side axle tube. To narrow the axle, approximately 2.875 inches are cut out from the driver’s side axle tube, and the tube is then welded back together. A separate passenger side axle is installed in the shortened driver’s side axle tube.
Please keep in mind that this information is specific to the Ford Explorer 8.8 rear axle and may not apply to other axle configurations or models of the Ford Explorer.
Contents
- How is axle length measured?
- How are Ford 9 axles measured?
- Which Ford Explorers have the 8.8 rear end?
- What years did the Ford Explorer have an 8.8 rear end?
- Why is the Ford 8.8 rear end so popular?
- How wide is the 8.8 axle on a Ford Explorer?
- How long is the axle on a 2000 Ford Explorer?
- How do I identify a Ford 8.8 axle?
- What are the lengths of wheel axles?
- What is the diameter of the Explorer 8.8 axle tube?
How is axle length measured?
How you go about measuring an axle depends on the axle type. Axles with yokes (front axle shafts) are measured from the center of the u-joint bore to the end of the splines. Semi-float and C-clip-equipped axle shafts are measured from the end of the shaft to the outer edge of the mounting flange.
How are Ford 9 axles measured?
Total width-this is the total width of the assembled rear end measured from the outside of one axle flange to the outside of the other. Backing plate to backing plate means nothing when measuring for a rear end so forget about that way of measuring.
Which Ford Explorers have the 8.8 rear end?
Word to the wise: Most ’91-’01 Ford Explorers came equipped with 31-spline 8.8s. The 8.8 is a C-clip rearend, which is another major weakness—if you break an axleshaft, it can come out of the housing, and you’ll lose the wheel and probably your quarter-panel along with it.
What years did the Ford Explorer have an 8.8 rear end?
2001-2005 Ford Explorer Sport Trac. 1991-2011 Ford Ranger 4.0L models. 1991-2001 Ford Explorer (Solid axle) 1985-2011 Ford Panther platform vehicles.
Why is the Ford 8.8 rear end so popular?
And, besides the reduced noise, the 8.8’s higher pinion location is more efficient, sapping less power than that of the 9-inch. And perhaps most important, there are OEM parts available for it. “You can still get Ford-built gear sets for an 8.8,” says Stein-Martin. “They’re the quietest – even quieter than aftermarket.
How wide is the 8.8 axle on a Ford Explorer?
The Ford Explorer 31-spline 8.8-Inch axle tube is 3.25 inches in diameter. The Ford F-150 / Bronco 31-spline 8.8-Inch axle tube is 3.25 inches in diameter. The Ford Mustang 8.8-Inch Axle tube is 2.80 inches in diameter.
How long is the axle on a 2000 Ford Explorer?
| Ford 8.8-Inch Axle – Specifications – Axle Shaft | ||
|---|---|---|
| Vehicle | Side | Length |
| 2003-2009 Ford Ranger FX4 | Left Hand | 30.125 Inch |
| 1995-2002 Ford Explorer | Right Hand | 27.620 Inch |
| 1995-2002 Ford Explorer | Left Hand | 30.500 Inch |
How do I identify a Ford 8.8 axle?
A Ford identifying tag is attached to one of the rear cover bolts. The four-letter code on the top right of the tag will be a dead giveaway as to whether you have found an 8.8-inch axle. The first three digits of these codes are listed with the original applications mentioned on the chart.
What are the lengths of wheel axles?
The most common front thru axle OLD dimensions are 100 mm, 110 mm, and 150 mm for front axles and 130mm, 135mm, 142mm, 148mm, and 197mm for rear axles. To accommodate both OLD sizes and dropout sizes, there are over 40 different thru-axle lengths on the market today.
What is the diameter of the Explorer 8.8 axle tube?
I know the explorer 8.8 rears are 3.25 for the axle tube diameter.
