AHG Auto Service » Make » Acura » How do you turn on the VTM 4 on an Acura MDX?

How do you turn on the VTM 4 on an Acura MDX?

Turning on VTM-4 on an Acura MDX
To turn on the VTM-4 (Variable Torque Management 4WD) on an Acura MDX, you don’t need to push a button to engage it. The VTM-4 system in the MDX is automatic and operates without any manual intervention. Under lower traction conditions, the VTM-4 system automatically transfers varying amounts of engine torque to the rear wheels.
It’s important to note that the VTM-4 lock button is different from the VTM-4 system itself. The VTM-4 lock button is used to engage the VTM-4 lock, which locks all four wheels together, providing maximum traction in low-traction situations. However, the VTM-4 lock is only available in certain conditions, such as when the vehicle is in gear 1 or 2, or when driving slowly on a slippery surface in reverse.
If you are experiencing issues with the VTM-4 system, such as a warning light or fault codes, it is recommended to have the vehicle scanned for diagnostic trouble codes (DTCs) to determine the specific cause of the issue. Common causes of the VTM-4 warning light include EGR valve failure and oxygen sensor issues .
Please note that the information provided here is based on general knowledge about the Acura MDX and may not apply to specific model years or variations. It is always best to consult the vehicle’s owner’s manual or contact an authorized Acura dealer for accurate and up-to-date information regarding the operation of the VTM-4 system on your specific Acura MDX model.
I hope this helps! Let me know if you have any other questions.

How do you turn off the VTM-4 on a Acura MDX?

do one of the following: Press the VTM-4 Lock button. Move the shift lever to D , D or D . Turn the ignition switch to LOCK (0). The VTM-4 Lock will temporarily disengage when the vehicle speed exceeds 18 mph (30 km/h).

How do I turn off VTM-4 lock?

To turn off vtm 4 in a honda pilot you will need to hold the button until the light turns off. With car started, press the vtm-4 lock button on the dash. Put foot on break and shift car into drive. Turn car off and put car into park.

Is Acura MDX always in AWD?

If you’re ready to take on Denver and Aurora roads at the helm of a new luxury crossover SUV, then you might be wondering, “Does the Acura MDX have AWD or 4WD?” The latest iteration of Acura’s premier third-row crossover comes with standard FWD on its first two packages but offers the upgraded Super Handling All-Wheel

What is VTM-4 Acura MDX?

VTM4 on an Acura MDX stands for Variable Torque Management 4WD System. This is the system that controls the amount of torque that gets applied to the rear wheels. What makes this system different is that it can control that torque independently for the rear wheels.

Is VTM-4 lock 4 wheel drive?

Honda Intelligent variable torque management (i-VTM4®) all-wheel drive is a sophisticated and technologically advanced AWD system that uses torque vectoring on the rear axle.

How do you put an Acura MDX in 4 wheel drive?

It’s automatic. You do not need to worry about it. The car will know when to use it and when not to use it. For really bad weather and really slow driving, you can put the car in 1st or 2nd gear and press the VTM-4 switch to “lock” the AWD.

What is the lock button on the VTM-4?

All you have to do is press the VT m4 again and then you can put the vehicle back into normal Drive. And drive away as usual.

How do you engage in VTM-4?

How Do I Engage The Lock?

  1. You must be at a complete stop or move no faster than 18 miles per hour.
  2. The shift lever must be on the first, second, or reverse gear.
  3. After all that, you press the “VTM-4” lock button between the instrument panel and the radio.
  4. An indicator light should illuminate if the lock was engaged.

How fast can you drive in VTM-4 lock?

You can lock the rear axles together and to the front axles with the VTM 4 button. (this is more than classic 4wd mode, since it also locks the rear differential) You must be in R, D1, or D2 gear and driving very slowly for VTM4 to engage. VTM 4 will automatically disengage partially at 6 mph, and fully at 18mph.

What would cause the VTM-4 light to come on?

System for example if you scan the onboard. Computer you got a p0442. Then there’s a problem in the EVAP system. And the computer’s seeing that there’s a leak.

AHG Auto Service

At AHG, we are committed to always providing our Perth customers with the best service and benefits when it comes to their vehicle servicing and repair needs. We have over 30 passenger and commercial vehicle dealerships in WA and can handle all of your car servicing needs no matter the make or model.

Leave a Comment