AHG Auto Service » Make » Subaru » How do you reset the window switch on a Subaru Outback?

How do you reset the window switch on a Subaru Outback?

Resetting the Window Switch on a Subaru Outback
To reset the window switch on a Subaru Outback, you can follow the procedure outlined below:
1. Close the driver’s door.
2. Turn the ignition switch to the ON position.
3. Open the driver’s side window halfway by pushing down the power window switch.
4. Pull up the power window switch and close the window completely. Continue pulling up the switch for approximately 1 second after the window is closed completely.
5. Open the driver’s side window completely by fully pushing down the power window switch.
This procedure should reactivate the auto up/down functions of the power window switch.
Please note that this procedure is specifically for the driver’s side window. If you are experiencing issues with the passenger window switch, you may need to consult the owner’s manual or seek assistance from a Subaru service center.
I hope this helps! Let me know if you have any other questions.

How do I reset my Outback driver window?

So all you needed to do was a simple reset push. And hold down push. And hold up for about five seconds. And everything we’re skin good to go.

Why won’t my Subaru Outback driver window go down?

The most common reasons a Subaru Outback window won’t go up or down are window’s electrical system such as a fuse or relay, a broken window motor, or a broken window regulator.

How do you reset a power window switch?

Hold the key down for 2-5 seconds after the window is down.
Once your window is all the way down, hold the button down for 2-5 seconds. Release the button after you’ve held it down for a short period of time. On some vehicles, the required time to reset the window is 2 seconds. On others, it is 5 seconds.

How do you reset the passenger side window on a Subaru Outback?

That can’t seem to do the passenger window. So how we fix this super super easy don’t fret all you’re gonna do is take your key. And we’re gonna turn this into accessory mode so it’s not the the first

How do you fix a Subaru window that wont go up?

How To Tackle A Faulty Subaru Window

  1. Open The Door Panel. To begin, you’ll need to remove the door panel.
  2. Remove The Window Switch.
  3. Disconnect The Window Switch Wiring Harness.
  4. Locate The Window Regulator.
  5. Remove All Wires And Adjusters.
  6. Install Window Regulator And Window Motor.

How do I reset my window motor?

And close the door. There’s the reset. Button press and hold the reset. Button roll the window down manually. Let off the switch. Let off the reset. Button. Now go up all the way.

How do you reset a Subaru window switch?

It’s really common it happens when you don’t use the feature a lot or you use the feature too. Much. It ends up happening a lot so it’s really easy to fix. You just put the window down all the way.

How do you reset the automatic window control?

Down. And hold the button down for five seconds. And then pull it all the way up. And once it’s all the way up hold the button for five seconds and that reprograms. It hope that helps.

How do you relearn a Subaru window?

Here is the procedure to reset: Push & hold the window button down for 10-15 seconds -then without letting go of the switch- Pull up on the window button for 10-15 seconds. This should reset the switch to work as it should.

How do you fix a Subaru window that won’t roll up?

On the passenger side window. So again windows up you roll down the window. All the way down. And you hold it for five seconds. And then you let go roll. It back up. Hold it again for five seconds.

AHG Auto Service

At AHG, we are committed to always providing our Perth customers with the best service and benefits when it comes to their vehicle servicing and repair needs. We have over 30 passenger and commercial vehicle dealerships in WA and can handle all of your car servicing needs no matter the make or model.

Leave a Comment