How do you reset the TPMS sensor on a Chevy Silverado?

To reset the TPMS sensor on a Chevy Silverado, you can follow these steps:
1. Start by ensuring that all tires are properly inflated to the recommended pressure. You can find the recommended tire pressure on the manufacturer’s sticker located on the inside of the driver’s door.
2. Once the tires are properly inflated, locate the trip odometer reset stem on the instrument panel.
3. Push and hold the trip odometer reset stem until the message “PRESS () TO RELEARN TIRE POSITIONS” is displayed on the instrument panel.
4. Release the trip odometer reset stem.
5. The horn will chirp twice to indicate that the sensor ID has been matched to the left front tire, and the TPMS sensor matching process is no longer active.
6. Repeat the process for the remaining tires in the following order: passenger side front tire, passenger side rear tire, and driver side rear tire.
7. After matching the sensor ID for all tires, turn off the ignition to complete the TPMS reset process.
It’s important to note that these instructions may vary slightly depending on the specific model year of your Chevy Silverado. If you’re unsure or need further assistance, it’s recommended to consult the owner’s manual or contact a certified Chevy repair center or tire shop for guidance.
Remember to always refer to the manufacturer’s instructions for the most accurate and up-to-date information on resetting the TPMS sensor on your Chevy Silverado.

How do you reset the service tire monitor system on a Chevy?

The Chevy “Service Tire Monitor System” Reset Process
The TPMS light and “service tire monitor system” warning can often be reset by adjusting your tire pressure to optimal levels and then driving around like you normally would for several minutes, followed by turning the car off, then back on.

Where is TPMS reset button?

Set the parking brake. Look for a button to the left of the steering column labeled with the TPMS icon if it’s there push and hold it until the TPMS indicator in the instrument panel blinks twice.

Can you relearn TPMS without tool?

With the exception of some models that may be relearned to the vehicle via a driving procedure, a TPMS scan tool is required to complete the vehicle relearn procedure.

How do you clear a service tire monitor?

Turn the car key to “on” but don’t start the vehicle. Press and hold the TPMS reset button until the tire pressure light blinks three times. Release the button and start the car. The light should go off within 20 minutes.

How do you calibrate the TPMS on a Chevy?

Turn your car off, and then turn the key to the “On” position without starting the car. Hold down the TPMS reset button until you see the tire pressure light blink three times. Then, release the button. Consult your owner’s manual if you have trouble finding the reset button.

How do you relearn a GM TPMS sensor?

Exit the vehicle and grab your TPMS relearn tool. Starting with the front driver’s-side tire, place the tip of the TPMS relearn tool against the tire sidewall near the wheel’s valve stem. Press the button on the tool to activate the sensor.

Can I reset my TPMS myself?

Hold the TPMS reset button until the tire pressure light blinks three times, then release it. Start the car and wait about 20 minutes for the sensor to refresh. You will find the tire pressure monitor reset button under the steering wheel. Refer to your vehicle’s owner’s manual if you can’t find it.

How do you reset the TPMS on a Chevy Silverado?

When the vehicle is off, turn the key to the “On” position, but don’t start the car. Find the TPMS reset button, usually under the steering wheel, and hold it down until the light flashes three times. Start the car and let it run for 20 minutes to give the sensor time to reset.

Where is the TPMS located?

The tire pressure sensor is typically found within the tire itself, mounted on the wheel assembly. These sensors relay crucial information to the vehicle’s computer, triggering the tire pressure sensor light when a discrepancy is detected.

Why won t my tire pressure light go off even though pressure is fine?

The causes can be a malfunction, or the weather changes. Other reasons why your TPMS light may still be blinking is because your tire may be damaged, or you might have gotten a recent tire replacement. Overall, the reasons can be vast, which is why it is best to take your car to a technician for professional diagnosis.