How do you reset the TPMS on a Ford Flex?

How to Reset TPMS on a Ford Flex
To reset the TPMS (Tire Pressure Monitoring System) on a Ford Flex, you can follow these steps:
1. Inflate the Tires: If the TPMS light is on, it may indicate low tire pressure. Inflate the tires to the recommended PSI (pounds per square inch) as specified on the Tire and Loading Information Label. This label can be found inside the driver’s side door or in the owner’s manual.
2. Drive at 50 mph: If the TPMS light persists after inflating the tires, drive the vehicle at 50 mph for ten minutes. This can help reset the TPMS and turn off the warning light.
3. Reset TPMS Manually: If the TPMS light continues to stay on, you may need to reset the TPMS manually using a TPMS Relearn Tool. Here is the process to relearn the TPMS on a Ford Flex:
a. Place your vehicle in the Park position and turn off the engine.

b. With the ignition key, turn the ignition from OFF to the ON position three times, ending in the ON position. If your vehicle has an ignition button, press the START/STOP button once to turn ON the ignition and then press it again to turn it OFF.

c. After the third time, leave the ignition in the ON position. This will initiate the TPMS relearn process.

d. Use the TPMS Relearn Tool to activate the TPMS sensors. Follow the instructions provided with the tool to complete the reset process .
By following these steps, you should be able to reset the TPMS on your Ford Flex. If you continue to experience issues or have further questions, it is recommended to consult your vehicle’s owner’s manual or contact a Ford dealership for assistance.
I hope this helps! Let me know if you have any other questions.

How do I manually reset my Ford TPMS?

And this procedure. Works just fine for that car as it does this car. So this is an automatic ford escape 2013 push button start.

How do you relearn a Ford TPMS with a push button start?

Manual relearn procedure (push-button start):
With the vehicle OFF, push and release the brake pedal. Push START button 5 times (NOTE: 8 times if 2x-to-RUN) Press and release the brake pedal. Push START button 6 times (NOTE: 9 times if 2x-to-RUN)

How do you reset the tire pressure light on a Ford Flex?

When the vehicle is off, turn the key to the “On” position, but don’t start the car. Hold down the TPMS reset button until the light blinks three times, then let go. Start the car and give the vehicle about 20 minutes for the sensor to reset.

How do you reset the tire pressure sensor on a 2016 Ford Flex?

Locate the TPMS reset button (usually beneath or near the steering wheel), and hold it until the light on the dashboard blinks three times. Release the button, start the ignition, and the light should be off. Add air to all tires (including the spare tire) to 3 PSI over the recommended amount.

How do you reset the TPMS light on a 2014 Ford Flex?

With and you’ll hear the horn. Sound let’s go ahead and navigate to the right front sensor press the green button. Now we’re at the right rear sensor. Now we will end at the left rear sensor.

Can I reset my TPMS myself?

Drive at or above 50 mph to reset the sensor for 10 minutes. This causes your sensor to reset the next time you turn on your car. With the vehicle off, turn the key to the “On” position, but do not start the car. Hold the TPMS reset button until the tire pressure light blinks three times, then release it.

Where is my TPMS located?

Where is the Tire Pressure Sensor Located? Typically, each wheel on your vehicle has a tire sensor mounted on the inside of the tire. Many vehicles use a specially designed tire valve that has the sensor integrated. Other vehicles may have the pressure sensor mounted to the inside of the wheel.

How do you relearn a Ford TPMS sensor?

How to enter the Ford TPMS learning mode?

1. Make the gear in P position.
2. Ignition switch to OFF, press and release the brake pedal.
3. Turn ignition switch from OFF position to RUN position 3 times and nd at RUN position.
4. Depress and release the brake pedal.
5. Ignition to OFF position.

Where is the TPMS reset button?

Set the parking brake. Look for a button to the left of the steering column labeled with the TPMS icon if it’s there push and hold it until the TPMS indicator in the instrument panel blinks twice.

How do you relearn a Ford tire sensor?

Locate the TPMS reset button (usually beneath or near the steering wheel), and hold it until the light on the dashboard blinks three times. Release the button, start the ignition, and the light should be off. Add air to all tires (including the spare tire) to 3 PSI over the recommended amount.