To reset the tire pressure sensor on a Chevy Captiva, you can follow these steps:
1. Set the parking brake.
2. Inflate all tires to the pressure listed on the placard.
3. Press the trip odometer button until “LEARN TIRE PRESSURES” is displayed. Then hold down the trip odometer button until the horn chirps.
4. Starting with the LF (left front) tire, use a properly formatted TPMS scan tool to scan each sensor in the following order: LF, RF (right front), RR (right rear), and LR (left rear). The horn will chirp after the vehicle has received a signal from each sensor. After activating the LR tire, the horn will chirp twice, signifying that the relearn is complete.
5. Turn the ignition to the OFF position.
Please note that you will need a TPMS tool or another properly formatted TPMS scan tool to perform this procedure .
I hope this helps! Let me know if you have any other questions.
Contents
- How do you calibrate a tire pressure sensor on a Chevy?
- How do you reset the service tire monitor system on a Chevy?
- Why won t my tire pressure light go off even though pressure is fine?
- Can I reset my tire sensors myself?
- Does every car have a TPMS reset button?
- How long does it take for tire sensor to reset?
- Where is the TPMS button located?
- Where is the reset button on the Chevy tire pressure sensor?
- How do you calibrate a tire pressure sensor?
- How do you reset tire pressure monitoring system?
How do you calibrate a tire pressure sensor on a Chevy?
Hold the TPMS reset button until the tire pressure light blinks three times and then release it. Start the car and wait 20 minutes for the sensor to refresh. The tire pressure monitor reset button is usually located beneath the steering wheel.
How do you reset the service tire monitor system on a Chevy?
The Chevy “Service Tire Monitor System” Reset Process
The TPMS light and “service tire monitor system” warning can often be reset by adjusting your tire pressure to optimal levels and then driving around like you normally would for several minutes, followed by turning the car off, then back on.
Why won t my tire pressure light go off even though pressure is fine?
The causes can be a malfunction, or the weather changes. Other reasons why your TPMS light may still be blinking is because your tire may be damaged, or you might have gotten a recent tire replacement. Overall, the reasons can be vast, which is why it is best to take your car to a technician for professional diagnosis.
Can I reset my tire sensors myself?
Once you have properly inflated your tires, the tire pressure light should automatically go off. However, if it doesn’t, there are a few different things that you can try: Drive at or above 50 mph to reset the sensor for 10 minutes. This causes your sensor to reset the next time you turn on your car.
It is worth pointing out that not all vehicles have a TPMS reset button, and the system may automatically reset itself once the tyre pressure is adjusted correctly. If you’re uncertain if your vehicle has a reset button, refer to the owner’s manual or get help from a local dealership.
How long does it take for tire sensor to reset?
Start the car and wait 20 minutes for the sensor to refresh. The tire pressure monitor reset button is typically located under the steering wheel. Refer to your vehicle’s owner’s manual if you’re unable to locate it. Inflate all tires to 3 PSI over their recommended amount, then deflate them completely.
The TPMS reset button is usually located beneath the steering wheel. If you can’t locate it, check your owner’s manual. Inflate all of your tires to 3 PSI over their recommended amount, then deflate them completely. Be sure to do the same thing to the spare tire, as it could also have a sensor.
The TPMS reset button is usually located underneath the steering wheel, but check your owner’s manual for its exact location.
How do you calibrate a tire pressure sensor?
Tire Pressure Monitoring System Calibration
- Pressing the TPMS button that is located on your steering column will start the process.
- Hold down the button until you see the indicator light blink twice.
- You’ll need to drive your vehicle for thirty minutes to re-calibrate the system.
How do you reset tire pressure monitoring system?
Step the calibration. Process will finish automatically within a few miles of driving. See your vehicle’s owner’s manual for more details or go to owners.honda.com for a downloadable version.
