How do you reset the SVC tire monitor system on a Chevy Cobalt?

To reset the SVC Tire Monitor system on a Chevy Cobalt, you can follow these steps:
1. Ensure that the tires are properly inflated and match the recommended tire pressures listed on the decal in the driver’s door.
2. Turn the vehicle to the “on” position with the engine off and roll down the driver’s window.
3. Press the odometer button until you see “LEARN TIRE PRESSURES” on the screen.
4. On the left side of the steering wheel, if you have four buttons, you can proceed with the reset process.
5. Go to a location where you can access excess air pressure and inflate each tire to at least 60 lb of pressure. It is important to note that the reset cannot be done unless each tire has at least 60 lb of pressure.
Please keep in mind that if you are not comfortable performing this procedure yourself, it is recommended to take your Cobalt to a dealership or an authorized service center for assistance.
I hope this helps! Let me know if you have any other questions.

What does SVC tire monitor mean Chevy Cobalt?

A Chevy “service tire monitor system” warning can mean one of two things. The first is that your tire pressure is suboptimal and requires adjusting to manufacturer-recommended levels. The second meaning applies if the warning does not go away after filling the tires or if a flashing TPMS light accompanies it.

Why does my car say SVC tire monitor?

When this warning message appears on your vehicle’s dashboard, it suggests that there may be a malfunction or fault within the TPMS itself or that one or more of the tire pressure sensors aren’t functioning properly. This usually means it’s time for a service appointment to see why the system needs service.

How do you reset a tire minder sensor?

How to Reset All Tires on a TireMinder TM-77, A1A or TM66 TPMS

1. Make sure you are in Monitoring Mode.
2. Press and hold the left and right buttons for 5 seconds until you hear a beep and see all 22 tire positions on the monitor.
3. Once you see all 22 tire positions, you can confirm you are in Learning Mode.

How do you reset the tire pressure sensor on a Chevy Cobalt?

Particular. Car put the parking brake. On turn the key to the on. Position hold down the info in the reset. Button for one. Second.

How do I reset my SVC tire monitor?

Resetting The TPMS System

1. Turn on the ignition, but don’t start the engine.
2. Press and hold the “SET” button for about 10 seconds until all four tires are displayed in your instrument panel.
3. Press and release the “SET” button again to clear all four tires from your display.

Where is the SVC tire monitor located?

Most service tire monitoring systems are built into the tires, which could fail if you hit a big pothole, or the sensors are too old. So most of the time, when you see the “Service Tire Monitoring System” warning light, you must replace parts that aren’t working right so the system can keep gathering data as it should.

Can you relearn TPMS without tool?

With the exception of some models that may be relearned to the vehicle via a driving procedure, a TPMS scan tool is required to complete the vehicle relearn procedure.

Can I drive with the SVC tire monitor on?

Since these systems often break down for reasons that have nothing to do with air pressure, you can still drive the car even though this light is on. But if you do, you should always keep an eye on the tire pressure. On the other hand, if your tire is flat, you shouldn’t drive your car unless you have to.

Can I reset my tire sensors myself?

Once you have properly inflated your tires, the tire pressure light should automatically go off. However, if it doesn’t, there are a few different things that you can try: Drive at or above 50 mph to reset the sensor for 10 minutes. This causes your sensor to reset the next time you turn on your car.

Where is the reset button on a Chevy TPMS?

The TPMS sensor should refresh within 20 minutes. The TPMS reset button is usually located underneath the steering wheel, but check your owner’s manual for its exact location.