How do you reset the remote start on a Dodge Ram?

To reset the remote start on a Dodge Ram, there are a few methods you can try based on the information from the search results:
Method 1: Turning the key to the On position and then Off again
– On both new and older Rams, you can try turning the key to the On position and then Off again to reset the remote start for three more restarts without using the key.
Method 2: Pressing the remote start button quickly three times
– If your remote start is not working and the truck is in service mode, you can try the following steps:
1. Turn the ignition key on and wait until the dash lights are done checking.
2. Press the remote start button quickly three times.
3. The dash lights should blink once or make a sound.
4. After doing this, the remote start should work again.
Method 3: Holding the unlock button on the key fob
– Another method to reset the remote start is by holding the unlock button on your key fob for 10 seconds until you hear silence. This method may work for different Dodge Ram models.
Please note that these methods may vary depending on the specific model and year of your Dodge Ram. It’s always a good idea to consult your owner’s manual for instructions or contact a dealership for assistance if needed.

What do you do when your remote start doesn’t work?

The following are some useful troubleshooting tips for when your remote starter refuses to work.

1. The Remote Isn’t Being Used Properly.
2. Check Your Fob Battery.
3. The Vehicle is Not in Park.
4. Your Key Fob is in the Car.
5. Too Many Remote Start Attempts.
6. Check the Hood.
7. Hazard Lights are On.
8. Coolant and Oil Pressure.

How do I reprogram my auto start key fob?

And then you do it to your other fob. And it’ll beep. Again. And now both of your fobs are programmed for your remote. Start.

Why is my key fob not working on push to start?

Check the battery: Make sure the battery in your smart key fob is not dead. If it is, replace the battery with a new one and try starting the car again. Check the signal: Make sure that the smart key fob is close enough to the vehicle to send a signal.

Why is my remote start not working and check engine light on?

If the ‘Check Engine Light’ or Malfunction Indicator Lamp (MIL) is illuminated, the remote start will not work. Don’t panic, one of the reasons the MIL can illuminate is due to a loose gas cap! Reseal the cap, restart the car, and retry step #1!

How do I resync my RAM key fob?

How to Reprogram A Key Fob

1. Enter your vehicle with your remote and key fob.
2. Insert the key into the ignition and turn it to the “RUN” position.
3. Press and hold the “UNLOCK” button on your remote for four seconds while pressing the “PANIC” button.
4. Press and release both the “LOCK” and “UNLOCK” buttons.

How do I get my check engine light to work on my remote start?

If there is a malfunction that’s turned on the light, the only way to get your remote start to operate is to repair the problem causing the light to illuminate.

How do I fix my remote start?

If you use your remote start twice in quick succession, the system will not work. This is by design and you can remedy this by getting into the vehicle, inserting the key into the ignition and turning it to “ON” and then “OFF” again. After doing that, get back out of the vehicle and try using the remote start again.

Why is my remote start disabled?

A dead battery, faulty starter, and an activated valet mode are some of the reasons why your remote start isn’t working. Aside from electrical issues, coolant and oil pressure problems can also affect the remote start’s operation. It costs between $250 and $400 to replace a damaged remote start fob.

How do I reset my remote start?

Resetting Your Remote Starter
Grab all of your car’s remote-start fobs. While in the driver’s seat, close the driver’s side door. Insert your ignition key and turn it to Accessory (or press the start button once without pushing the brake pedal). Press the Lock button on your remote car starter.

How do I reprogram my Dodge key fob push start?

Enter your vehicle and press and release the lock button on your remote five times within ten seconds upon entering the car. Insert your key into the ignition and turn it to the “RUN” position. For four seconds, press and hold the “UNLOCK” and “PANIC” buttons simultaneously. Then, release at the same time.