How do you reset the liftgate on a Subaru Forester?

How to Reset the Liftgate on a Subaru Forester
If you are experiencing issues with the liftgate on your Subaru Forester, there are several methods you can try to reset it:
Method 1: Manual Reset
To manually reset the liftgate, you can follow these steps:
– With the ignition OFF, open the liftgate manually using a fluid motion. No light flash or beep should occur.
– Carefully close the liftgate until the first audible click of the latch mechanism is heard, then immediately let go of the liftgate.
Method 2: Using the Rear Gate Opener Button
According to the owner’s manual, if the liftgate is closed, the reset procedure involves keeping the rear gate opener button pressed until the liftgate resets.
Method 3: Disconnecting the Battery
Some users have reported success in resetting the liftgate by disconnecting the negative battery lead and touching it on the positive to reset the computer. After reconnecting the lead, the problem was resolved.
Method 4: Holding the Rear Liftgate Close-Button
Another method involves holding the rear liftgate close-button until it beeps four times. This button is located on the door jamb of the rear liftgate and is only accessible when the liftgate is open and not moving.
It’s important to note that if these methods do not resolve the issue, it may be necessary to consult the service manual or seek assistance from a Subaru dealership for further diagnostic procedures.
Remember to refer to your specific model’s owner’s manual for detailed instructions on resetting the liftgate.
I hope these methods help you reset the liftgate on your Subaru Forester! If you have any further questions or concerns, feel free to ask.

Why wont my Subaru trunk open?

If you hold the button on the hatch itself for several seconds, it’ll beep and reset itself. If that doesn’t work, dealer may have to look at it. Make sure you press the door unlock button on the driver’s side door before doing the long press on the hatch button on the dash.

Is it bad to manually open a power liftgate?

The only drawbacks are that they are a more expensive option than a manual liftgate and are more expensive to fix if something breaks. For that reason, a lot of people ask, “Can I manually open and close my power liftgate?” The simple answer is yes.

How do I reset my Subaru rear gate?

How to reset your Subaru rear hatch. When this issue is occurring, the car will beep three times each time you press the rear gate button. The natural response is to release the button once the car beeps. To reset the rear door, keep holding the rear hatch release button until you hear a soft “thuck”.

Why is my lift gate not working?

The most common liftgate issues can be traced back to the motor or motor start solenoid. If you hear a clicking noise when the switch is activated, more than likely you have a bad solenoid. Using a small jumper cable, bypass the solenoid by putting direct power to the motor to see if it will run.

Why is my trunk not closing?

While everyone argues about WD-40, please check the trim around your trunk opening. I’ve seen this happen several times where someone thought it was the latch, and it really was that the trim had lifted slightly and was preventing the trunk lid from actually closing far enough to latch.

How do you manually open a Subaru trunk?

So go ahead. And pull the top lever. Up we’ll go outside the vehicle. You can see that it’s open.

How do I know if my liftgate actuator is bad?

Symptoms of a bad trunk lock actuator include the trunk refusing to lock or close, the automatic trunk pull-down not working, and the trunk not opening with the key fob but opening with the traditional key.

Why is my automatic liftgate not working?

A lift strut issue, a malfunctioning power hatch, and a bad switch or button are some of the common reasons why a power liftgate may malfunction. The buttons, fuses, and electrical connectors must be inspected to diagnose a power liftgate issue.

How do I fix my Subaru trunk not closing?

Solution – while the hatch was down, Hold the button under the Subaru emblem for 10 seconds. This was a hard reset and after that the hatch worked as normal. Easy, no worries.

How do you reset the sensor on a Subaru?

Dynamic Drive Reset: Take a drive at 50 mph or faster for 10 minutes. This helps trigger a sensor reset, which could resolve the issue upon the next ignition. Key Position Reset: Turn the key to the “On” position without starting the engine.