How do you reset the electronic parking brake on a Subaru?

Resetting the Electronic Parking Brake on a Subaru
If you need to reset the electronic parking brake (EPB) on your Subaru, you can follow these steps:
1. Understanding the Working Principle:
– When you engage your Subaru’s EPB, an electronic module sends a signal to a motor in the rear calipers. The motor then spins the force sensor, which pushes the piston out and squeezes the brake pads onto the brake disc.
2. Resetting the EPB:
– To reset the EPB, you need to hold the brake switch down (release EPB) when withdrawing the key. If the switch is pressed too many times in a short amount of time, the system goes into standby mode for roughly one minute to allow the motor to cool down.
3. Common Issues and Troubleshooting:
– If you encounter difficulties releasing the electronic parking brake, you can use the electronic parking brake release tool. However, it’s recommended to contact your Subaru dealer for inspection as soon as possible if you experience persistent issues.
It’s important to note that the EPB system in Subaru vehicles is a convenient feature, but it’s always best to consult the manufacturer’s guidelines or seek professional assistance if you encounter persistent issues with the EPB.
I hope this information helps you effectively reset the electronic parking brake on your Subaru! If you have any further questions or need additional assistance, feel free to ask.

What causes electric parking brake problem?

Electric parking brakes rely on an electrical system to activate and release the brake mechanism. Electrical malfunctions can occur due to issues with the wiring, connectors, or blown fuse. If there is a problem with the electrical components, the parking brake may not engage or release as intended.

Is it OK to drive with EPB light on?

If the parking brake warning light is still on even though the EPB has been released, have the system checked by a professional workshop. Kia recommends to visit an authorised Kia dealer/ service partner. Do not drive your vehicle with the EPB applied. It may cause excessive brake pad and brake rotor wear.

What is the electronic parking brake warning light on a Subaru?

Electronic parking brake system warning
The brake system warning light flashes when the electronic parking brake system is malfunctioning. If the warning light flashes, promptly park in a safe location as soon as possible and contact your SUBARU dealer.

How do you manually release an electronic parking brake?

With the AUTO switch OFF, the EPB can be applied by pushing and holding the parking brake switch. This will work with the ignition switch ON or OFF and with the vehicle moving or stationary. To release the brake, pull and hold the manual switch while at the same time pressing the brake pedal.

What is the recall on the Subaru electronic parking brake?

(Subaru) is recalling certain 2010-2014 Subaru Legacy and Outback vehicles equipped with a manual transmission. The electronic parking brake (EPB) may not engage as intended, allowing the vehicle to rollaway if the transmission is not in the proper gear when parked. A vehicle rollaway can increase the risk of a crash.

What is the most common cause of parking brake failure?

Improperly adjusted parking brakes are a frequent cause of failure. When the parking brake is not adjusted correctly, it may not engage fully or provide sufficient force to hold the vehicle in place, particularly on steep inclines.

What is the problem with the electronic parking brake on a Subaru Outback?

Description of the WTV-81 Safety Recall:
The Electronic Parking Brake (or EPB) Actuator recall is due to a manufacturer defect in a component of a circuit board in the control unit of the EPB. The actuator stroke sensor magnetic ring within a capcitor of the ciruit board can become cracked.

How do I reset my electric parking brake?

This step is crucial as it initiates while holding down the control observe. The indicator lights on your dashboard. These lights may vary depending. On the make and model of your vehicle. Typically.

What causes parking brake fault?

Broken or Damaged Springs
Springs within the parking brake mechanism provide the necessary tension and force to engage and disengage the brake system. If these springs become broken or damaged, the parking brake may not engage fully and cause a park brake fault.

Will disconnecting battery reset parking brake?

Disconnect your vehicle’s battery to reset the parking brake system. In rare cases, your vehicle’s computer may just need to be reset.