How to Relearn the TPMS on a Dodge Ram 1500
To relearn the TPMS (Tire Pressure Monitoring System) on a Dodge Ram 1500, you can follow these steps:
1. Check the TPMS sensor information: Before replacing a TPMS sensor, it is important to check the sensor information to ensure you are working with the correct frequency. Starting mid-year 2009, RAM 1500 vehicles manufactured with 433MHz TPMS sensors.
2. Perform a hard reset: If the TPMS light comes on after swapping to aftermarket wheels or changing the TPMS sensors in your tires, you can perform a hard reset on the vehicle. To do this, remove the negative battery terminal and let the battery sit unconnected for 10-15 minutes. Then, reconnect the battery. This will cause all of the vehicle’s systems, including the TPMS, to relearn various operating parameters.
3. Drive the vehicle: After performing the hard reset, drive the vehicle for at least 5 minutes at 28 mph. This will allow the TPMS sensors to transfer the new sensor IDs to the vehicle’s ECU (Electronic Control Unit).
It’s important to note that the specific steps for relearning the TPMS on a Dodge Ram 1500 may vary depending on the model year and the type of TPMS system installed. Therefore, it is recommended to consult the vehicle’s owner’s manual or reach out to a certified Dodge dealership for the most accurate and up-to-date instructions.
Please let me know if there’s anything else I can help you with!
Contents
- Can you relearn TPMS without tool?
- How do you relearn the TPMS on a 2017 Dodge Ram?
- How do you clear the code on a 2015 Ram 1500?
- Where is TPMS reset button on Ram 1500?
- Where is TPMS reset button?
- How do you reset the TPMS on a Dodge Ram?
- How do you relearn a Dodge TPMS?
- How do you relearn the TPMS on a 2015 Dodge Ram 1500?
- What is the relearn procedure for TPMS?
- What are the three most common relearn procedures?
Can you relearn TPMS without tool?
With the exception of some models that may be relearned to the vehicle via a driving procedure, a TPMS scan tool is required to complete the vehicle relearn procedure.
How do you relearn the TPMS on a 2017 Dodge Ram?
To reset Your 2017 Dodge Ram 2500 tire pressure sensor, inflate all tires to the pressure listed on the placard. Let the vehicle sit OFF for a MINImum of 20 minutes. Drive the vehicle above 15 MPH for at least 10 minutes. The relearn may take from 10-35 minutes of driving.
How do you clear the code on a 2015 Ram 1500?
There’s just three simple steps that will get you back on the streets of Cedar Park worry-free!
- Turn your battery off by disconnecting the negative cable.
- Wait for 20 minutes to reset the RAM 1500 check engine light.
- Reconnect the negative cable.
Start your car and wait 20 minutes for the TPMS sensor to refresh. The TPMS reset button is usually located beneath the steering wheel.
Set the parking brake. Look for a button to the left of the steering column labeled with the TPMS icon if it’s there push and hold it until the TPMS indicator in the instrument panel blinks twice.
How do you reset the TPMS on a Dodge Ram?
How Can I Reset the TPMS Light?
- Drive your car at 50 mph for 10 minutes to reset the sensor.
- Find a place to park and turn off your car completely.
- Turn your key to the “On” position without turning the car back on.
- Press the TPMS reset button and hold until the light blinks three times.
- Release the button.
How do you relearn a Dodge TPMS?
Right. Front right rear and left rear wheels. Then you must drive the vehicle. For up to 20 minutes at 15 miles per hour or more the VT fifty-six bonus obd to relearn procedure.
How do you relearn the TPMS on a 2015 Dodge Ram 1500?
Auto relearn procedure, years 2008-2020 (including RAM 1500 DS/DT/DX):
- Confirm TPMS sensors are properly installed.
- Adjust tire pressure to placard value.
- Hold TPMS tester on left front tire sidewall next to the valve stem, use TPMS tool to activate the sensor.
- Repeat for the right front, right rear and left rear sensors.
What is the relearn procedure for TPMS?
TPMS Vehicle relearn procedures vary by automaker. Some vehicles relearn automatically when you drive them. Others require a TPMS scan tool to complete the relearn. The process for many Asian makes and models may also require connecting a tool to the OBDII connection.
What are the three most common relearn procedures?
The three types of relearn procedures are auto relearn, stationary (manual) and OBD. Some vehicles may use a combination of two or more relearn types.
