How do you relearn the TPMS on a Chevy Malibu?

To relearn the TPMS (Tire Pressure Monitoring System) on a Chevy Malibu, you can follow these steps:
1. Start from the driver-side front tire and place a TPMS Relearn Tool against the tire sidewall near the valve stem.
2. Press the button on the TPMS Relearn Tool to activate the TPMS sensor.
3. Repeat the process for the passenger-side front tire, passenger-side rear tire, and driver-side rear tire.
4. After resetting the last tire, turn off the ignition.
5. Adjust the tire pressure in all four tires to the recommended amount indicated on the tire placard.
6. Put the valve covers back on the valves after filling the tires with the correct pressure.
Please note that these instructions are based on the Chevy Malibu owner’s manual and the information provided in the search results. It’s always a good idea to consult the owner’s manual for your specific vehicle model for the most accurate instructions.
If you don’t have a TPMS Relearn Tool, you may need to use a TPMS activation tool specific to your vehicle model. The specific tool and relearn procedure may vary depending on the year and model of your Chevy Malibu.
Remember, it’s important to follow the recommended procedures to ensure the TPMS is properly reset and functioning correctly.

Why won t my tire pressure light go off even though pressure is fine?

The causes can be a malfunction, or the weather changes. Other reasons why your TPMS light may still be blinking is because your tire may be damaged, or you might have gotten a recent tire replacement. Overall, the reasons can be vast, which is why it is best to take your car to a technician for professional diagnosis.

How do you relearn the TPMS on a 2018 Chevy Malibu?

Manual relearn procedure (2006-2020):

1. OBDII connector is not required.
2. Confirm TPMS sensors are properly installed.
3. Adjust tire pressures to placard value.
4. Turn ignition to ON.
5. Press and hold lock and unlock button on the key fob until horn sounds.
6. Activate TPMS Tool on left front tire sidewall next to valve stem.

How do you reset the TPMS on a Chevrolet Malibu?

Hold the TPMS reset button, and the tire pressure light should blink three times. Then, release the button and start your car. The TPMS sensor should refresh within 20 minutes.

How do you relearn the TPMS on a Chevy?

Once the TPMS light is on, hold the TPMS reset button until the icon flashes three times. Start your vehicle and wait about 20 minutes to allow the sensor to reset. To find your TPMS reset button, check out your vehicle owner’s manual! Usually the button is under the steering wheel.

Can I reset my TPMS myself?

Hold the TPMS reset button until the tire pressure light blinks three times, then release it. Start the car and wait about 20 minutes for the sensor to refresh. You will find the tire pressure monitor reset button under the steering wheel. Refer to your vehicle’s owner’s manual if you can’t find it.

Why wont my tire pressure monitor light go off?

However, if the TPMS light remains on, there are a few things you can do: Drive at or above 50 mph for 10 minutes to reset the sensor. This can cause your sensor to reset when you turn on your vehicle. With the vehicle off, turn the key to the “ON” position, but do not start it.

Will disconnecting my battery reset my TPMS?

Most TPMS sensors have their own batteries, so the sensor just reports low pressure coming from them. If disconnecting the battery made the TPMS “forget” what 32psi (or whatever the setting is) was, the system would be useless.

Where is TPMS reset button?

Set the parking brake. Look for a button to the left of the steering column labeled with the TPMS icon if it’s there push and hold it until the TPMS indicator in the instrument panel blinks twice.

Where is the TPMS switch located?

It is typically located beneath the steering wheel, near the driver’s sidekick panel, or on the dashboard. Once you’ve found the TPMS reset button, press and hold it for approximately three seconds.

Can you relearn TPMS without tool?

With the exception of some models that may be relearned to the vehicle via a driving procedure, a TPMS scan tool is required to complete the vehicle relearn procedure.