How do you regenerate the DPF on a Ford Transit?

Regenerating the DPF on a Ford Transit
To carry out a DPF regeneration on a Ford Transit, you can follow these steps:
1. Drive at Legal Motorway Speeds in a Lower Gear: When a regeneration is being called for but not triggered, you can press the upper + button to upshift, press the lower button to downshift, and shift back to drive (D) to switch the feature off. Then, drive the van at legal motorway speeds in a lower gear to initiate a DPF regeneration.
2. Use a Diagnostic Scanner: You can use a Ford Transit diagnostic scanner to perform forced DPF regeneration and diagnostics. This tool enables you to read and erase fault codes, graph live data, perform an EVAP test, O2 sensor test, oil light reset, ABS testing, and most importantly, perform a forced DPF regen when the DPF light comes on.
3. Consider Professional Cleaning: If the DPF continues to have issues even after attempted regenerations, you may consider having the DPF professionally cleaned. There are mobile vans that provide a cleaning service, including diagnostics, cleaning of the DPF, and removing stubborn carbon deposits as part of the vehicle’s regeneration processes.
It’s important to note that DPF regeneration is a critical maintenance task for diesel vehicles, and it’s essential to address any DPF-related issues promptly to ensure the vehicle’s optimal performance.
I hope this information helps! If you have any further questions, feel free to ask.

How do you regenerate a DPF on a Ford Transit?

The second step is to try DPF regeneration….

1. Ford Transit Regeneration process.
2. The engine is at normal operating temperature.
3. Drive the vehicle at a minimum speed of 40mph for 15 minutes @ 2000 rpm.
4. Regeneration has completed the DPF light should switch off.

How do I manually start DPF regeneration?

Process if the manual process won’t begin ensure the engine is up to temperature. If it’s not raise the temperature as previously discussed and then restart the process.

Can you force a DPF regeneration while driving?

In a first stage, the DPF warning light goes on. In most cases, driving for 10 minutes at 65 km/h (about 40 mph) or faster will ensure proper regeneration.

Can you force a regen in limp mode?

Unfortunately if your car is already in limp mode the automatic regeneration will no longer happen, it needs to be driven by diagnostic equipment and if the soot content is too high it needs to be ‘forced’ and a dealership can’t do it.

Can a fully blocked DPF be cleaned?

Whilst you can buy DPF cleaner designed to flush out the insides of your car when regeneration cannot be completed, this won’t help to unblock a significantly blocked DPF. A professional DPF clean is the best option if you really want to notice a difference in the quality of your car’s diesel particulate filter.

How do you regen manually?

Because that’s how long the regen the manual regeneration is going to take you get to your safe spot. You pull over put the truck in neutral. Set the parking brake.

How do I unblock my DPF filter without removing it?

How to unblock a DPF? 1) DPF Regeneration – Find a motorway near you where you can drive at 70+ MPH for 30-45 minutes; this should provide the optimal conditions for the regeneration process to complete. If this works, consider a regular drive along a motorway regularly to allow the regeneration process to complete.

How to do a parked DPF regeneration?

And apply the parking brake making sure not to touch the foot pedals. Finally press and hold the parked regen switch for two seconds then release.

What causes DPF to not regen?

Failure of a regen may lead to an engine shut down. Pay attention to your CEL (Check Engine Light) as this may disable a DPF regen process. There are multiple reasons that may prevent a DPF regen. These include, but are not limited to, a clogged DPF filter, EGR fault codes, your VGT turbo operation.

How do you initiate a regen?

And apply the parking brake making sure not to touch the foot pedals. Finally press and hold the parked regen switch for two seconds then release.