How do you put a jack stand on a Subaru Outback?

Placing Jack Stands on a Subaru Outback
When placing jack stands on a Subaru Outback, it’s important to ensure that the car is supported safely and securely. Here’s how you can do it:
Locating Jack Points:
To lift the car, you can use the pinch welds as close to the wheel as possible. Just inboard of the notches in the pinch weld, there are little flat pad areas that can be used as jack points. It’s important not to put the stands or a floor jack directly on the pinch weld. Additionally, the central jacking points in the 2020 Outback are at a jacking plate between the oil pan and the transmission pan, and the rear differential housing .
Placing the Jack Stands:
After lifting the car, place the jack stands as close to the jack as possible. Slowly release the jack a bit so the car is resting on the stand. This ensures that the weight is properly supported, allowing you to work on the car confidently.
It’s important to follow the guidelines provided in the car’s manual for the specific model year. The manual typically provides detailed instructions on the proper jack and jack stand points for the vehicle.
Remember to always prioritize safety when working under a vehicle, and if you have any doubts, it’s best to consult the vehicle’s manual or seek professional assistance.
I hope this helps you confidently and safely work on your Subaru Outback!

What to do if you don’t have jack stands?

Yes you can use a jack without stands. you can use wooden blocks to secure the car from falling on you if the jack fails. Or in the case of using a jack to change a flat tire as long as you stay out from under it you should be fine without using jack stands or some kind of block to secure it.

Can you put jack stands under the axle?

It depends what you are working on! If I were working on the axle, I’d put them under the chassis frame (or jacking points on a monocoque vehicle), but if I was working on the shell, brakes, diff etc I usually put them under the axle tube.

Where do you put the jack stands on a Subaru Outback?

So you have on the Subarus. You have to lift points front and back my deck my lift jack is on it already. So we’re the pinch rail. That’s what they call this part of the body underneath.

Is it OK to put jack stands on wood?

With no warning, the car can shift as the asphalt gives way. Prevent this by using something like a chunk of wood to spread the load of the jack stand to a larger area. The same applies for any soft substrate like gravel or dirt.

How do I get my car up on a jack stand?

Jack the car on level ground, chock the wheels on the opposite axle to the one your lifting, jack up with floor jack and place jack stands on frame of car, be careful when jacking and placing jack stands, failure to prevent the car from rolling, improper jacking and placement of stands can damage the car or it can fall …

How do you install a jack stand?

Jack stands must be placed directly under the lifting point. There should be enough room at every jack point to accommodate the stand’s grip. When releasing hydraulic pressure from the floor jack, a properly rated jack stand will hold the weight of the car as long as the stand is flat.

Where do jack stands go in the rear?

Locate the jack point on the vehicle
Your owner’s manual should give you the location of jack points. Usually there’s one on each side behind the front wheels and in front of the back wheels, close to the rocker panels. There may be central jack points located behind the bumpers (front and rear).

Can you put jack stands on the axle?

It depends what you are working on! If I were working on the axle, I’d put them under the chassis frame (or jacking points on a monocoque vehicle), but if I was working on the shell, brakes, diff etc I usually put them under the axle tube.

Where do you put the jack on a Subaru?

Finally place the jack stands under the pinch welds. And lower the floor jack ing up the car from the back can be done in a pretty similar way just like the last time we’ll be chalking off our Wheels.

Where do I put jack stands?

Place the jack stand under the car frame at reinforced point or “pinch weld” near where the jack is placed. Pin-type jack stands use locking pins to adjust the height, while screw-type jack stands use adjustable screws.