How do you grease Dodge Ram ball joints?

How to Grease Dodge Ram Ball Joints
To grease the ball joints on a Dodge Ram, you will need to follow specific steps depending on the type of ball joint and whether it has a grease zerk fitting or not. Here are some general guidelines based on the information found in the search results:
1. Upper Ball Joints: The upper ball joints on some Dodge Ram models have grease zerk fittings on the top, making them easily accessible for greasing. You can use a needle tip for your grease gun to inject grease into the zerk fitting. Aftermarket u-joints may require a different fitting, which you can find at auto parts stores like NAPA.
2. Lower Ball Joints: The lower ball joints on some Dodge Ram models also have grease zerk fittings, typically located on the top of the joint. To grease them, you may need to jack up the axle and rotate the tire to gain clearance. Use a grease needle attached to your grease gun to inject grease into the zerk fitting.
3. Sealed Ball Joints: Some Dodge Ram models have sealed ball joints that do not have grease zerk fittings. These ball joints are not designed to be greased and should be replaced when they wear out.
It’s important to note that the specific procedure for greasing ball joints may vary depending on the year and model of your Dodge Ram. It’s recommended to consult the vehicle’s owner’s manual or reach out to a certified mechanic for detailed instructions tailored to your specific vehicle.
Remember to always use the appropriate type and amount of grease recommended by the manufacturer when greasing ball joints.
I hope this information helps! Let me know if you have any other questions.

How do you lubricate ball joints?

As you can see there’s a fitting right here. That is called a grease zert take my grease gun and it’ll pop right in on. It. Take and give her a couple pumps.

Do sealed ball joints need grease?

Most manufactureres use sealed ball joints that do not come with grease zerk fittings. Theoretically, these ball joints will not need any extra grease and are sealed up tight so contaminates can’t get inside, but if you notice a groaning while turning then the culprit might be a grease-thirsty ball joint.

How often should you grease ball joints on a truck?

As a general rule, it’s advisable to lubricate your ball joints every time you change your vehicle’s oil. Typically, an oil change occurs every 3,000-5,000 miles, so this would be a safe and adequate estimate for when to apply grease.

Do ball joints with grease fittings come pre greased?

It’s going to be greased from the factory, and most ball joints are not even greasable anymore – usually lasting till the boot fails. I would say that generally speaking the joint is not going to last much longer than the cheap rubber boot that keeps water and other contaminants out.

What is the best lubricant for ball joints?

Fluorocarbon Gel 880: Grease for Ball Joints
Nye’s Fluorocarbon Gel 880 is a PTFE-thickened, heavy viscosity dimethyl silicone grease with excellent water resistance and structural stability under a wide temperature range and is our recommended solution for most ball joint applications.

Can you over grease a ball joint?

Give each ball joint just enough grease to fill the ball joint area and then stop. And if you keep greasing the ball joint until a sealed boot pops, that’s where the water and dirt will now enter and give the ball joint a short life.

Can you use red and tacky grease for ball joints?

It’s hard to give Lucas Oil’s Red ‘n’ Tacky the pick for Best Value as opposed to Best Overall. This grease has a lot going for it and is an excellent multipurpose grease to keep around the shop for lubricating various parts of your car or truck, including the ball joints.

What is the best grease for ball joints and suspension?

NLGI #2 is the most widespread classification and is used in many automotive and heavy-duty applications, such as ball joints and other suspension components. Chances are you’ve used an NLGI #2 grease before.

What happens if ball joints are not greased?

Without grease the ball wears allowing excess movement of the joint and eventual failure, which can be serious as most of these are part of the vehicles steering system.

Do you need an alignment after replacing ball joints?

There’s no denying that it’s very important to replace your ball joints when needed. However, it’s worth noting that doing that doesn’t necessarily mean you need an alignment. The only time you need one after replacing the ball joints is if the previous alignment was performed when ball joints were not in good shape.