How do you drain the coolant on a 2014 Ford Edge?

To drain the coolant on a 2014 Ford Edge, you can follow these steps:
1. Gather the necessary tools and materials:
– Safety goggles and gloves
– Drain pan or bucket
– Pliers or a wrench
– New coolant/antifreeze
2. Prepare the vehicle:
– Make sure the engine is cool before starting.
– Park the vehicle on a level surface and engage the parking brake.
– Open the hood and locate the coolant reservoir.
3. Drain the coolant:
– Place the drain pan or bucket under the radiator drain plug or lower radiator hose.
– If your vehicle has a drain plug, use pliers or a wrench to loosen and remove it. Allow the coolant to drain completely into the pan.
– If your vehicle doesn’t have a drain plug, you can remove the lower radiator hose to drain the coolant. Loosen the hose clamp with pliers and carefully remove the hose, allowing the coolant to drain into the pan.
4. Dispose of the old coolant:
– Coolant is toxic and harmful to the environment, so it’s important to dispose of it properly. Check with your local recycling center or auto parts store for guidance on how to dispose of the old coolant safely.
5. Refill with new coolant:
– Close the drain plug or reattach the lower radiator hose.
– Refill the coolant reservoir with the recommended type and amount of new coolant/antifreeze. Refer to your vehicle’s owner’s manual or consult a Ford dealership for the specific coolant requirements for your 2014 Ford Edge.
– Start the engine and let it run for a few minutes to circulate the coolant. Check the coolant level and add more if necessary.
Please note that these instructions are a general guide, and it’s always a good idea to consult your vehicle’s owner’s manual or seek professional assistance for specific instructions and recommendations for your 2014 Ford Edge.

What coolant does a 2014 Ford Edge use?

Peak OET North American yellow 50/50 pre-diuted; 1 gallon.

What is the easiest way to drain coolant?

Locate the Drain Plug and Loosen
This is found on the bottom of the radiator. Place a pan under the drain plug to catch old coolant. Loosen the drain plug and allow coolant to flow. Tighten the drain plug when coolant has stopped flowing.

Can you drain coolant yourself?

The valve should have a bolt at the end, which is often covered by a plastic top that can be easily removed with a screwdriver. Wearing gloves, twist open the bolt on the valve (you may need to use a socket and ratchet, or a spanner). The coolant/antifreeze will begin to drain out.

How often should you change the coolant in a Ford Edge?

How often should you change coolant in a Ford Edge? Typically, you should have your Ford Edge coolant flush completed every 30,000 miles or every two years. There are some instances where your car can go without a flush for a longer period of time.

Is it better to flush or drain and refill coolant system?

The downside of that is a drain and fill will leave stuff behind…contaminants, rust particles, thick and goopy coolant that was once smooth and effective. A coolant flush, though, is performed with a machine that forcefully cleans and pushes out old fluid and all that other junk you don’t want in there.

Do you have to drain coolant or just top off?

In many cases, it’s enough to simply top up the coolant reservoir in your engine, but sometimes, your vehicle may need a coolant flush. During this procedure, a mechanic will completely empty the old coolant from your car. They will then top your reservoir up and make sure that your car hasn’t suffered any damage.

How much coolant does a 2014 Ford Edge take?

Capacities and Specifications

Item	Capacity
Engine coolant.	12.4 qt (11.7 L)
Brake fluid.	Between MIN/MAX on brake fluid reservoir
Rear differential fluid.	28.07 ± 1.01 fl oz (830 ± 30 ml)
Power Transfer Unit (PTU) fluid.	12.7 ± 1.7 fl oz (375 ± 50 ml)

How do you flush a radiator without removing it?

You will want to place your hose or water source onto the inlet valve of your radiator, turning on the water supply to the hose and flushing the radiator out. Continue to run water through the radiator until all the water exiting the radiator is clear and free from sludge or debris.

What is the difference between a coolant exchange and a flush?

When it’s time for a coolant exchange, it’s not just about adding new coolant. The old coolant is likely dirty, and simply topping it up would compound the issue. The fluid flush process involves draining the entire cooling system and replacing it with fresh coolant.

How can I drain my coolant tank?

To empty the system, let the engine cool, take the cap off the expansion tank, put the heater control inside the car on ‘hot’, and open the drain tap or remove the bottom hose. Open the bleed screws on the hoses and connections. They are usually thumbscrews and can be opened with the fingers.