How do you drain the coolant in a 2012 Dodge Avenger?

How to Drain Coolant in a 2012 Dodge Avenger
To drain the coolant in a 2012 Dodge Avenger, you can follow these steps:
1. Use a Wet Dry Shop Vac: Use a wet dry shop vac and take the filter off. Open the radiator cap and vacuum the majority of the coolant out. Then, pull the lower hose to drain the remainder. It’s important to note that you may have to pull both block plugs if you want to completely drain the coolant.
2. Locate the Petcock or Lower Radiator Hose: The coolant can also be drained by opening the petcock or removing the lower radiator hose. If you have the underbody splash shields, there will be a hole cut-out in the splash shield under the bumper on the front right side of the car to accommodate the draining of the coolant.
3. Follow the Coolant Flush Procedure: The coolant flush procedure involves draining the coolant from the reservoir and then draining the coolant from the radiator by opening the petcock or removing the lower radiator hose.
It’s important to follow these steps carefully to ensure the proper draining of the coolant from the 2012 Dodge Avenger.

How do you empty engine coolant?

And loosen the drain plug. This will typically be on the left or right side of the radiator. At the bottom allow the coolant to drain. Next move your catch pan underneath the engine.

How do you drain the coolant in a 2013 Dodge Avenger?

Allow the coolant to completely drain. Out while the coolant is draining check the condition of the radiator hoses heater hoses and clamps replace any damaged clamps or hoses.

Do you need to flush coolant or just drain?

If you have something that’s over 10 years old and if you’re unsure about it, FLUSH IT. Contaminated/old coolant will start to carry rust/dirt particles through your engine and can cause a variety of bad things to occur, namely corrosion. For most people a drain and refill periodically is all you will ever need.

What is the easiest way to drain coolant?

Locate the Drain Plug and Loosen
This is found on the bottom of the radiator. Place a pan under the drain plug to catch old coolant. Loosen the drain plug and allow coolant to flow. Tighten the drain plug when coolant has stopped flowing.

How full should your antifreeze tank be?

“When the engine is cool, open your hood, and locate the coolant reservoir. The coolant level should be between the F(full) and L(low) marks on the side of the coolant reservoir.”

What coolant does Dodge Avenger use?

ZEREX – G05 50/50 Ready-to-Use Antifreeze / Coolant, 1 Gallon (Part No. ZXG05RU1) ZEREX G05® is the automaker approved original chemistry used in newer Ford®, Chrysler® and Mercedes-Benz® automotive and diesel engines.

How do you drain coolant without a drain plug?

In general, the easiest way to drain coolant from systems like these is to disconnect the lowest fitting between the coolant hose and the engine block and let the coolant just drain out. Usually, it’s near the bottom of the block itself, so it shouldn’t be hard to reach from underneath the vehicle.

How much coolant does a 2012 Dodge Avenger hold?

Coolant Capacity 6.8 L (7.2 qt.)

What happens if you drain coolant?

Simply draining the radiator may get rid of most of the old antifreeze but could leave some coolant and contaminants behind, which would then mix with and pollute your new antifreeze and cause overheating. You want a full flush, a forced removal of anything old so you can pave the way for new fluid.

Is it OK to drive with empty coolant?

That’s why the moment you notice leaking coolant or a low coolant dashboard warning light, you should seek a comprehensive coolant service. In short, the answer to “Can you drive without coolant?” is a resounding “No,” and ignoring the low or no coolant warning signs can result in a vehicle that no longer functions.