How do you check the transmission fluid on a Subaru Legacy?

Checking the Transmission Fluid on a Subaru Legacy
To check the transmission fluid on a Subaru Legacy, you can follow these steps:
1. Park the vehicle on a level surface and turn off the engine. It’s important to ensure that the car is parked on a level surface to get an accurate reading.
2. Locate the transmission dipstick. The transmission dipstick is usually located near the back of the engine compartment. It is typically labeled and has a bright-colored handle for easy identification.
3. Remove the dipstick. Once you’ve located the dipstick, pull it out of the dipstick tube.
4. Wipe the dipstick clean. Use a clean cloth or paper towel to wipe off any transmission fluid from the dipstick.
5. Reinsert the dipstick. After wiping the dipstick clean, insert it back into the dipstick tube fully.
6. Remove the dipstick again. Pull out the dipstick once more to check the fluid level.
7. Check the fluid level. Look at the end of the dipstick to see where the fluid level is. There are usually two marks on the dipstick indicating the minimum and maximum levels. The fluid level should be between these two marks.
8. Add fluid if necessary. If the fluid level is below the minimum mark, you will need to add transmission fluid. Use a funnel to pour the fluid into the transmission through the dipstick tube. Be careful not to overfill it.
9. Check the fluid condition. While checking the fluid level, also pay attention to the color and smell of the fluid. Transmission fluid should be a clear reddish color and have a slightly sweet smell. If the fluid is dark, cloudy, or has a burnt smell, it may indicate a problem and should be inspected by a professional.
It’s important to note that the Subaru Legacy uses special transmission fluid in its automatic transmissions, which you can either purchase from Subaru or find an auto parts store that carries fluid approved for use in Subaru transmissions.
Remember to always consult your vehicle’s owner’s manual for specific instructions and guidelines on checking the transmission fluid for your particular Subaru Legacy model.
I hope this helps! Let me know if you have any other questions.

How do you check the transmission fluid on a 2013 Subaru Legacy?

Then turn the engine. Off locate the check fill plug on the side of the transaxle remove the plug. The fluid should be level with the bottom of the hole. Or just trickle.

How do I check if my transmission fluid is low?

With the engine warmed up, leave the car idling in park on a level surface. Pull out the dipstick, wipe it clean, replace it slowly, and then pull it back out. Check the fluid level—how high the fluid comes up on the dipstick—against the “full” and “low” or “fill” marks on the dipstick.

How to check transmission fluid level when there is no dipstick?

Case removing the fill plug will allow you to add more fluid. Third all sealed transmissions must have the fluid checked at a specified temperature otherwise.

Where is the transmission fluid dipstick on a 2017 Subaru Legacy?

Open the hood and then find the looped handle near the back of the engine. That’s the Subaru transmission fluid dipstick. Be sure you are grabbing the transmission dipstick instead of the oil dipstick.

Will the check engine light come on if the transmission fluid is low?

The check engine light comes on to let the driver know that there is a problem in one of the vehicle’s systems. A trouble code or dash light does not necessarily mean the transmission fluid is low, but a low transmission fluid level will cause the check engine light to illuminate on most modern vehicles.

How do you check the transmission fluid on a 2016 Subaru Legacy?

Shift the transmission in each position before setting it in park. Leave the engine idling. Open the hood and then find the looped handle near the back of the engine. That’s the Subaru transmission fluid dipstick.

Can you just add transmission fluid if it’s low?

Yes, you can add transmission fluid without changing it. However, it is important to keep in mind that adding new fluid to old fluid may not always be the best solution.

Where is the transmission fluid dipstick?

Locate automatic transmission fluid dipstick.
Typically near where the transmission or transaxle meets rear of the engine. It looks similar to the oil dipstick.

How do you check the transmission fluid on a 2017 Subaru Legacy?

Checking Your Transmission Fluid

1. Turn your engine on for a few minutes before proceeding.
2. Find the transmission fluid dipstick.
3. Remove the dipstick and touch the fluid, moving it around between your thumb and forefinger.
4. Use a rag to wipe off the dipstick.
5. Use a funnel to bring the fluid level up to the right spot.

How do you check the transmission fluid level on a Subaru?

Shift the selector level in each position. Then shift it in the “P” position, and run the engine at idling speed. Pull out the dipstick and check the fluid level on the gauge. If it is below the lower level on the “HOT” side, add the recommended automatic transmission fluid up to the upper level.