How do you check the codes on a Chevy Equinox without a scanner?

Checking Chevy Equinox Codes Without a Scanner
If you need to check the codes on a Chevy Equinox without a scanner, there are a few methods you can try:
1. Resetting the Check Engine Light: You can reset the check engine light in a Chevy Equinox without any OBD diagnostic scanner tools. One method is to turn the key from on to off three times, then drive the car. Another way is to unplug the battery under the hood for 10 minutes and reconnect it. However, it’s important to note that if the problem has not been addressed, the light will turn on again once the error code is triggered.
2. Allowing the Light to Turn Off Naturally: In some cases, the check engine light on your Chevy Equinox will shut itself off if the issue or code that caused it to turn on is fixed. For example, if the cause of the check engine light coming on was a loose gas cap, tightening it may turn the light off. Similarly, if your catalytic converter is going functional and you did a lot of stop-and-go driving, the light may go off after about 20-40 miles. If the light remains on after driving over that amount, it’s advisable to bring the vehicle in for a double-check and reset of the code.
3. Using Diagnostic Trouble Code Charts: You can also pull GM Engine Diagnostic Trouble Code Charts for OBD I systems to check for codes without a scanner.
It’s important to keep in mind that while these methods may help in certain situations, having access to an OBD-II scanner is crucial for a more comprehensive diagnosis of any issues with your Chevy Equinox.
If you have any further questions or need additional assistance, feel free to ask!

How do you read a Chevy engine code?

The prefix portion of the ID code tells you the engine assembly plant code, and the engine’s assembly date (for example, 0701 = July 1st…. no year is indicated). The suffix portion tells you the original application, vehicle model, engine RPO/ transmission / horsepower, etc…

How do I look up codes for my car?

To access these codes:

1. Locate the OBD 2 port. This port is typically located beneath the dashboard, near the driver’s seat.
2. Plug in a scanner. Use an OBD 2 scanner, readily available at AutoZone, or consult your vehicle’s manual to determine if it has a built-in diagnostic tool.
3. Read the codes.

How can I check my engine code without a code reader?

Method 1: Use Your Odometer Reset to Check Engine Light Codes

1. Step 1: Press and hold the odometer’s reset button.
2. Step 2: While holding the odometer’s reset button, press and hold the odometer’s trip button.
3. Step 3: While holding down both the odometer’s trip and reset buttons, turn the ignition switch to “on”

Can you clear check engine light without code reader?

You can disconnect the battery for at least a few minutes and then reconnect it and that will usually clear the light. If you do not disconnect the battery and if the fault that caused the light to illuminate in the first place has been repaired, the light should go out on its own after a few drive cycles.

How can I check my car code at home?

How to Use An OBD Scanner

1. Connect The Scanner. Your OBD scanner will have a connection cable with a 16-pin trapezoidal plug at the end.
2. Turn The Key. Insert your key in the ignition, but don’t start the engine.
3. Type In Your Vehicle Identification Number.
4. Locate Your OBD Codes.
5. Decipher Your Codes.

How do you get a check engine light code without a Chevy scanner?

Now we got P0420. Now we have P0455. And then it’ll say done that means it read all of its codes. Now.

Can AutoZone check my codes?

AutoZone offers a complimentary Fix Finder service that efficiently diagnoses warning lights, including Check Engine, ABS, and maintenance indicators. Simply visit your nearest AutoZone store when a warning light appears on your vehicle’s dashboard.

How do I display check engine codes?

How to Read OBD 2 Codes

1. Step 1: Locate Your OBD 2 Port. The OBD 2 port is typically located beneath the dashboard on the driver’s side of the vehicle, and it may also be near the center console.
2. Step 2: Use an OBD 2 Scanner.
3. Step 3: Plug in the Scanner.
4. Step 4: Read the Codes.

How do I find my Chevy engine code?

Engine Code Stamping Numbers
The location of this code depends on the type of engine, typically as follows: Small Block Chevy: Machined pad in front of the passenger side cylinder head. Often hidden by the alterator. Big Block Chevy: Machined pad in front of the passenger side cylinder head or above timing chain cover.

Can I use my phone as a car code reader?

OBD Fusion® is an app for iPhone, iPad, iPod Touch, and Android that allows you to read diagnostic data from your vehicle. You can create virtual dashboards showing multiple vehicle sensors, estimate fuel economy, read diagnostic trouble codes, and turn off your check engine light.